manualshive.com logo in svg

Honeywell V48A, Product Data, Page: 8 / 12

Share
Download
Honeywell V48A Product Data Download Page 8

V48A,F,J; V88A,J DIAPHRAGM GAS VALVES

60-2080—9

8

Fig. 8. Installing optional 126590 adjustable bleed valve.

Fig. 9. Installing optional bleed orifice.

OPERATION

Operation of the V48 and V88 Valves  

(Fig. 10)

When the controller is not calling for heat, the coil is 

de-energized. The plunger in the 3-way actuator is in the 

DOWN position so the bleed port is closed and the supply port 

is open. Gas flows into the top part of the valve. The gas 

pressure on top of the diaphragm, the weight, and the spring 

hold the valve closed.

Fig. 10. Operation of V48 and V88 diaphragm gas valves.

On a call for heat, the controller contacts close and the coil is 

energized. This pulls the plunger to the UP position, opening 

the bleed port and closing the supply port. The gas in the top 

BLEED TAPPING

126590 ADJUSTABLE BLEED VALVE

SLEEVE

COMPRESSION NUT

1/4 INCH

TUBING

7/16-24 UNS

ADJUSTING SCREW

7/16 INCH HEX

1/8-27 NPT

M7290

BLEED PORT

1/8-27 NPT

M7298A

1/8 INCH DIAMETER ROD

BLEED ORIFICE

(SELECTED)

GAS 

SUPPLY

PASSAGE

BLEED 

PORT

PLUNGER

SPRING

WEIGHT

DIAPHRAGM

MAIN 

GAS

SUPPLY

TO BURNER

VALVE CLOSED

GAS 

SUPPLY

PASSAGE

BLEED 

PORT

PLUNGER

SPRING

WEIGHT

DIAPHRAGM

MAIN 

GAS

SUPPLY

TO BURNER

VALVE OPENING

GAS 

SUPPLY

PASSAGE

BLEED 

PORT

PLUNGER

SPRING

WEIGHT

DIAPHRAGM

MAIN 

GAS

SUPPLY

TO BURNER

VALVE OPEN

M8489

Summary of Contents for V48A













Reviews:

No comments