Honeywell TB3 Series Installation Instructions Manual Download Page 24 | Manualshive

Page: 24 / 24

Honeywell TB3 Series Installation Instructions Manual Download Page 24

TB3 SERIES COMMUNICATING THERMOSTATS INSTALLATION INSTRUCTIONS

Honeywell Building Technologies

715 Peachtree St NE

Atlanta, Georgia 30308

buildings.honeywell.com

® U.S. Registered Trademark

©2022 Honeywell International Inc.

31-00576-01 I Rev. 11-22

The material in this document is for information purposes only. The content and the product described are subject to change without notice.
Honeywell makes no representations or warranties with respect to this document. In no event shall Honeywell be liable for technical or editorial
omissions or mistakes in this document, nor shall it be liable for any damages, direct or incidental, arising out of or related to the use of this
document. No part of this document may be reproduced in any form or by any means without prior written permission from Honeywell.

WEEE DIRECTIVE

WEEE Directive 2012/2019/EC Waste Electrical and Electronic Equipment Directive.

• At the end of the product life dispose of the packaging and product in a corresponding recycling center.

• Do not dispose of the unit with the usual domestic refuse.

• Do not burn the product.

«
...
22
23
24

Summary of Contents for TB3 Series

























Reviews:

No comments