background image

Honeywell Safety and Productivity Solutions 

9680 Old Bailes Road
Fort Mill, SC 29707 
www.honeywell.com

32313758-B-EN  |  10/16
© 2016 Honeywell International Inc.

WARRANTY/REMEDY

Honeywell warrants goods of its manufacture as being free of 
defective materials and faulty workmanship during the applicable 
warranty period. Honeywell’s standard product warranty applies 
unless agreed to otherwise by Honeywell in writing; please refer 
to your order acknowledgement or consult your local sales office 
for specific warranty details. If warranted goods are returned to 
Honeywell during the period of coverage, Honeywell will repair or 
replace, at its option, without charge those items that Honeywell, 
in its sole discretion, finds defective. 

The foregoing is buyer’s 

sole remedy and is in lieu of all other warranties, expressed 
or implied, including those of merchantability and fitness for 
a particular purpose. In no event shall Honeywell be liable for 
consequential, special, or indirect damages.

While Honeywell may provide application assistance personally, 
through our literature and the Honeywell web site, it is buyer’s 
sole responsibility to determine the suitability of the product in 
the application.

Specifications may change without notice. The information we 
supply is believed to be accurate and reliable as of this writing. 
However, Honeywell assumes no responsibility for its use.

Honeywell serves its customers through a worldwide network of 
sales offices, representatives and distributors. For application 
assistance, current specifications, pricing or name of the nearest 
Authorized Distributor, contact your local sales office or:

E-mail: [email protected]
Internet: sensing.honeywell.com
Phone and Fax: 
USA/Canada  

+1-800-537-6945

International  

+1-815-235-6847; +1-815-235-6545 Fax

    

 

WARNING

PERSONAL INJURY

DO NOT USE these products as safety or emergency stop 
devices or in any other application where failure of the product 
could result in personal injury.

Failure to comply with these instructions could result in 
death or serious injury.

Summary of Contents for PX3 Series








Reviews: