background image

W4365B_DE_1204     Seite 11/11

PEHA Lichtsteuerung  –  PEHA Elektro GmbH & Co. KG a Honeywell Company · Gartenstraße 49 · 58511 Lüdenscheid · Deutschland · www.peha.de · [email protected]

Safety

CAUTION! Danger of electrical shock!

The housing contains current-carrying components. 

Contact can lead to personal injury! All work on the mains 

network and the device may only be done by an authorised 

electrician.

•  Disconnect power supply from the device.
•  Secure the device against being powered on again.
•  Check that the device is powered off.
•  Close the housing securely before applying power. 

This device is only intended to be used for its stated application. 

Unauthorised conversions, modifications or changes are not 
permissible! This device may not be used in conjunction with 
other devices whose operation could present a hazard to people, 
animals or property.

The following must be observed:

•  Prevailing statutes, standards and regulations.
•  State-of-the-art technology at the time of installation.
•  The device’s operating instructions.
•  Operating instructions can only cite general stipulations. 

These are to be viewed in the context of a specific system.

General Information

Disposal of the device

Do not dispose of old devices in the household waste! The device 
must be disposed of in compliance with the laws and standards of 
the country in which it is operated! The device contains electrical 
components that must be disposed of as electronics waste. The 
enclosure is made from recyclable plastic.

Warranty conditions

These operating instructions are an integral part of both the device 

and our terms of warranty. They must be handed over to the 
user. The technical design of the appliance is subject to change 
without prior notification. PEHA products are manufactured and 
quality-checked with the latest technology according to applicable 
national and international regulations. Nevertheless, if a product 
should exhibit a defect, PEHA warrants to make remedy as follows 
(regardless of any claims against the dealer to which the end user 
may be entitled as a result of the sales transaction): In the event of 
a justified and properly-established claim, PEHA shall exercise its 
prerogative to either repair or replace the defective device. Further 
claims or liability for consequential damage are explicitly excluded. 

A justifiable deficiency is deemed to exist if the device exhibits a 

structural, manufacturing, or material defect that makes it unusable 
or substantially impairs its utility at the time it is turned over to the 
end user. The warranty does not apply to natural wear, improper 
usage, incorrect connection, device tampering or the effects of 
external influences. The warranty period is 24 months from the 
date of purchase by the end user from a dealer and ends not later 
than 36 months after the device’s date of manufacture. German law 
shall be applicable for the settlement of warranty claims.

Technical Data

OPERATING VOLTAGE:    

 

230V ~ 50Hz (UK & Europe)

SWITCH CAPACITY:  

 

 

10 Amps max any lighting load except incandescent lamps:  

 

 

1500W max (at 230V~)

MAXIMUM RECOMMENDED 
LOAD (DSI/DALI):  

 

 

25 Ballasts

MAXIMUM RECOMMENDED 
MOUNTING HEIGHT:    

 

3.5m

RANGE:   

 

 

Adjustable up to 20m

OFF DELAY:  

 

 

1 min - 96 hours plus 10-second walk-test mode

PHOTOCELL:  

 

 

Passive/Active/Regulating adjustable 50-5000 lux

MATERIAL:  

 

 

Flame retardant PC/ABS

COLOUR:  

 

 

White

WEIGHT:  

 

 

160g

IP RATING:   

 

 

IP4X

GB

Disposal and recycling:

At the end of their useful life the packaging and product should be disposed 
of via a suitable recycling centre.
Do not dispose of with normal household waste.
Do not burn. 

Summary of Contents for PEHA LightSpot D MR2500DALIFR4












Reviews: