manualshive.com logo in svg

Honeywell MS4105A1030, Installation Instructions Manual, Page: 9 / 12

Share
Download
Honeywell MS4105A1030 Installation Instructions Manual Download Page 9

3 NM, 5 NM SERIES SPRING RETURN DIRECT COUPLED ACTUATORS

9

62-0274—07

Fig. 20. Wiring for 3 position Economizer controllers, MS74 series.

Fig. 21. Wiring for Sylk BUS, MS31 series.

OPERATION

The actuator is designed to be used in ventilating and air 

conditioning installations to operate valves, dampers, 

ventilation flaps and louvers. (For ratings, see the 

Specifications section.) If the power fails, the actuator will 

spring return to the fail safe position.

When using a proportional controller, the actuator drives 

toward its fully open position when the input signal increases; 

the actuator drives toward the fully closed position when the 

input signal decreases. The actuator stops when the input 

signal reaches the desired proportional control point. This 

operates in reverse when set to a 10-2(0) position.

IMPORTANT

The actuator is designed to respond to DDC 

Controller instantaneous contact closures. Take care 

not to short cycle the actuator. Unstable damper 

control can cause premature actuator failure.

Actuator Override

To override the control signal (for freeze protection or similar 

applications):

1.

Override to full open:

a. Disconnect the input signal (from terminal 3).

b. Apply 24 Vac to terminal 3.

c. See Fig. 22.

2.

Override to full closed:

a. Disconnect the input signal (from terminal 3).

b. See Fig. 23.

Fig. 22. Override to full open.

ACTUATOR

V

FEEDBACK

5

4

3

1

2

M32679

3 POSITION

MINIMUM POSITION

1

EXTERNAL MINIMUM POSITION POT 
CAN BE APPLIED TO 4 90°-0°.

SET SWITCH TO 3 POSITION.

2

2-10 VDC
10-2 VDC
3 POSITION
MINIMUM POSITION
Fltg, fwd
Fltg, rev

2

SENSOR

24 VAC

–

+

1 = ADDRESS 11
2 = ADDRESS 12
3 = ADDRESS 13
4 = ADDRESS 14
5 = ADDRESS 15
6 = TEST

S-BUS

LINE VOLTAGE POWER SUPPLY.  PROVIDE 
DISCONNECT MEANS AND OVERLOAD 
PROTECTION AS REQUIRED.

24 VDC SUPPLY ACCEPTABLE.

0/2..10 VDC INPUT

0/2..10 VDC OUTPUT

M32548

1

2

1

2

S-BUS

24 VAC

ACTUATOR

MS3105J ONLY

1

2

3

4

5

S-BUS

S-BUS

V

S3

S2

S1

ACTUATOR 

0/2 TO 10 VDC 
PROPORTIONING 
CONTROLLER 

24 VAC 

1

1 

2 

3 

2 

LINE VOLTAGE POWER SUPPLY.  
PROVIDE DISCONNECT MEANS AND  
OVERLOAD PROTECTION AS REQUIRED. 
 
24 VDC SUPPLY ACCEPTABLE. 
 
SET SWITCH TO MODULATING. 

V 

FEEDBACK

– 

 

+ 

 

FEEDBACK 

5

4 

3 

1 

2 

M27827

2-10 VDC 
10-2 VDC 
0-10 VDC 
10-0 VDC 
Fltg, fwd 
Fltg, rev 

3 

SPDT 

0°-90° OR +

90°-0° OR N/A

Summary of Contents for MS4105A1030













Reviews:

No comments