manualshive.com logo in svg

Honeywell MS4105A1030, Installation Instructions Manual, Page: 6 / 12

Share
Download
Honeywell MS4105A1030 Installation Instructions Manual Download Page 6

3 NM, 5 NM SERIES SPRING RETURN DIRECT COUPLED ACTUATORS

62-0274—07

6

NOTE: This cover can be removed before or after mounting 

actuator to the damper shaft or valve linkage.

In order to wire the device, the access cover must be removed 

as follows:

1.

Remove the screw from the center of the cover, set the 

screw aside.

2.

Pull the cover along the long axis of the actuator.

3.

If the actuator is not yet mounted, set it aside.

4.

Remove conduit dust covers.

5.

Thread wire through conduit holes.

6.

Connect wires as appropriate to the terminal block(s). 

(See Fig. 9 and 11.)

NOTE: Use either 1/2 in. x 14 NPS or M20 x 1.5 strain 

relief or conduit adapters.

Fig. 8. Removing access cover.

Typical Wiring Without Cables

See Fig. 9 through 23 for typical wiring details for actuators 

without cables (whips). See Fig. 24 through 26 for wiring 

actuators with cables (whips).

Fig. 9. Terminal block details.

Fig. 10. Terminal block details.

Fig. 11. S-BUS Terminal block details.

M27719

S3 S2 S1

5

4

3

2

1

M27720

90° -0°

OR

N/A

90° -0°

OR

+

1

POWER SUPPLY.  PROVIDE DISCONNECT MEANS AND 
OVERLOAD PROTECTION AS REQUIRED.

S3

S2

S1

FEEDBACK

ACTUATOR

1

5

3

1

2

M32677

4

T

S-BUS

1

POWER SUPPLY.  PROVIDE DISCONNECT MEANS AND 
OVERLOAD PROTECTION AS REQUIRED.

S3

S2

S1

ANALOG OUTPUT

ACTUATOR

1

5

3

1

2

M32677

4

T

S-BUS

Summary of Contents for MS4105A1030













Reviews:

No comments