background image

in the house after the system is armed. Certain devices such as the door and motion sensors can 

be on delay. The delay time will be set up between you and the installer. There are multiple ways 

to arm your system for away. The first way is to use one of the “

ARM AWAY

” buttons that is 

on your keypad.   

   

 When you use either of these buttons you need to either put in 

your four digit code or press the quick arm button. 

 The second way to arm your system 

for stay is to use the wireless keyfob that came with your system. To use the keyfob simply press 

and hold the arm away button 

 for about 5 seconds. Once you do either of these methods for 

arming away the keypad will then look like this  

 

The second mode for arming your system is known as 

STAY

. Stay is for people who 

have motion sensors installed. If you 

DO

 

NOT

 have motion sensors installed the only action stay 

does for you is a silent count down for the alarm to turn on as normal. If you 

DO

 have motion 

sensors installed when you arm for stay everything 

BUT

 the motion sensors will be armed. To 

reiterate when armed in 

STAY

 your motion sensors 

WILL

 

NOT

 be on so you can freely move 

around the house and still be protected by other devices (i.e. glassbreaks, door/window switches) 

To arm in 

STAY

 mode push and hold the shortcut button on your keypad that says arm stay

 The second way to arm in stay mode is to push and hold the button on your keyfob that 

has a little man inside a house. 

 Once you have armed the system the keypad will read 

"

ARMED

 

STAY

 

EXIT

 

NOW

" (similar to the large picture above) 

Turning your system OFF

 

 

Turning your system off or disarming the system, as it is called, is different than 

arming the system when done at the keypad. To disarm the system from the keypad all 

you have to do is push the green disarm button and put in your four digit code or when 

you walk through the delay door it will automatically ask for your four digit code you 

will then enter your code. Another way to disarm your system is to push and hold the 

unlocked lock button 

 located on the keyfob. 

 

Summary of Contents for LYNX TOUCH L5200






Reviews: