background image

IPGSM-DP Commercial Fire Communicator – Installation and Setup Guide

 

 

– 

10

 – 

iGSM Communications Module Information 

 

TB 1

6
7
8

5

10
11

9

2
3
4

1

PRIMARY POWER: 9 - 16.5 VAC
CURRENT: 900mA PEAK, 70mA STANDBY
BATTERY: 8V. 3.1 AHr FOR 24 Hr BACKUP

FCC:XXXXXXXXXX    IC: YYYYYYYYYY

RSSI

M0

M1

GPRS

IBS

iPGSM-COM-002-V1

RSSI / Mode
and
status LEDs

ON – Message transmission pending.
QUICK PERIODIC BLINK – Normal.
FAST BLINK – Message waiting for network ACK.
SLOW BLINK – Idle power abnormal.
SLOW BLINK – In unison with green LED,
                          registratration in progress.

Ethernet Link/Activity
GREEN 

ON  –  Ethernet Link detected.
OFF – No link detected.
FAST BLINK – Transmitting/Receiving Data.

Link Speed
GREEN 

Network Collision
YELLOW

Note:

 If all LEDs FAST BLINK in unison with

          the RSSI LEDs this indicates a Hardware Error.

ON – No contact with network.
OFF – Normal.
SLOW BLINK – Loss of communication with the

                       Dialer Capture Module

 (ECP fault).

ON – NOT registered with AlarmNet.
OFF – Registered with AlarmNet.
FAST BLINK – Download session with Compass
                         in progress.
SLOW BLINK – In unison with yellow LED,
                          registration in progress.

Mode
Switch

Tamper

Switch

GRN

YEL

RED

ECP

Zone  (NOT USED)

4204  (NOT USED)

2 - 4204  (NOT USED)

MODULE'S RECEIVED SIGNAL STRENGTH (RSSI)

When the 

Mode Switch

 is NOT depressed, LED 1 will illuminate red.

The remaining LEDs indicate RSSI (Received Signal Strength).

MODULE'S OPERATION MODE

When the 

Mode Switch

 IS depressed, LED 1 will be OFF.

   LEDs 2 and 3 indicate the  module's communication mode with the Dialer Capture Module.

Mode                                LED 2 (yellow)                           LED 3 (yellow

)

MODULE'S STATUS

When the 

Mode Switch

 IS depressed, LED 1 will be OFF.  

  LEDs 4, 5, and 6 indicate the module's Status.

FAST BLINK - Module registered, second

site available, excellent signal strength.

LED 4 (green)                     LED 5 (green)                                  LED 6 (green)

ON - Connected to

Internet.

ON - Module registered, no second

site available.

ON - GPRS service

available.

OFF - No GPRS service

available

OFF - Module not registered with

network carrier.

FAST BLINK - GPRS in

use.

SLOW BLINK - Module registered, second

site available, and low signal strength.

NORMAL BLINK - Module registered, second
site available, acceptable signal strength.

OFF - Not connected

to Internet.

7720P
Programmer
Port

BLINKING – Network collision detected.
OFF – Normal.

ON – 100 MB/S link to Internet.
OFF – 10 MB/S link to Internet.

FAST BLINK – No network contact AND loss of communi-
                        cation with the 

Dialer Capture Module

.

OFF

ON

OFF

ON

OFF

OFF

ON

ON

 

 

Summary of Contents for IPGSM-DP

















Reviews: