manualshive.com logo in svg

Honeywell IFP1000, Installation And Operation Manual, Page: 19 / 50

Share
Download
Honeywell IFP1000 Installation And Operation Manual Download Page 19

Hardware Installation

151153

3-1

Section 3
Hardware Installation

RPS-1000 installation involves the following steps:

•

AC power (Section 3.1) and backup battery connection (Section 3.2).

•

Physical connection to the IFP-1000 or IFP-1000ECS FACP to the controlling RPS-1000 
(see Section 3.3).

•

Setting an ID for the RPS-1000 (Section 3.3.1).

•

Physical connection of SBUS modules that will be powered by this RPS-1000 (Section 
3.4). 

•

Physical connection of any outputs (conventional relays, notification appliances, auxiliary 
power modules, and so on) that will be powered by this RPS-1000. See Section 3.5.1 for 
notification appliance wiring information. Refer to the IFP-1000 Installation Manual (PN 
151139) or IFP-1000ECS Installation Manual (PN 151460), for software configuration 
information and other information about installing outputs.

3.1

AC Power

At installation, connect the AC terminals to 120 VAC source as shown in Figure 3-1. It 
may be necessary for a professional electrician to make this connection.

The AC terminals are rated as 120 VAC, 50 or 60 Hz, 2.7 A (for the RPS-1000) or 240 
VAC, 50 or 60 Hz, 1.4A (for the RPS-1000HV).   

Figure 3-1  AC Power Connection

To 120 VAC

Power Source

Wh

ite

Green

Black

For RPS-1000

For RPS-1000HV

To 240 VAC

Power Source

Earth

(Ground)

Note: RPS-1000HV 
models are labeled.

Summary of Contents for IFP1000



















































Reviews:

No comments