manualshive.com logo in svg

Honeywell IFP1000, Installation And Operation Manual, Page: 20 / 50

Share
Download
Honeywell IFP1000 Installation And Operation Manual Download Page 20

Hardware Installation

151153

3-2

3.2

Battery Connection

The RPS-1000 battery charge capacity is 7.0 to 33.0 AH. Use 12V batteries of the 
same AH rating. Determine the correct AH rating as per your current load calculation 
(see Section Table 2-4).

Note: When your backup batteries requirements use backup batteries that are to large to fit into the 

RPS-1000 cabinet. The AB-33 cabinet holds batteries up to the 33 AH size. (Refer to IFP-1000 
Installation manual PN 151139 or IFP-1000ECS Installation manual PN 151460 for AB-33 instal-
lation instructions.

Wire batteries in series to produce a 24-volt equivalent. Do not parallel batteries to 
increase the AH rating.

Figure 3-2  Battery Connection

3.3

Connecting the RPS-1000 to the FACP

1. Connect the RPS-1000 to the appropriate SBUS. The RPS-1000 can be connected directly 

to the IFP-1000 / IFP-1000ECS FACP or can be daisy-chained to another RPS-1000. Fig-
ure 3-3 and Figure 3-4 show both connections.

2. Use on-board DIP switch to assign an ID#. (See Section 3.3.1) Figure 2-1 shows the loca-

tion of the DIP switches on the RPS-1000 board.

Red

To Panel

Black

UL Listed 12V Battery

UL Listed 12V Battery

Battery Jumper

(P/N 140694)

Replace batteries every 5 years.

Gell Cell

Gell Cell

Summary of Contents for IFP1000



















































Reviews:

No comments