Honeywell FSL100-IR3 Technical Handbook Download Page 44

Page: 44 / 57

MAN0987_Iss 2_09/16

FSL100 Series Flame Detectors

Technical Handbook

CERTIFICATION

13 Accessory Specifications

FSL100-TL Safe Area Test Lamp Specifications

Lamp Housing

ABS (plastic) black

Ingress Protection rating

IP30 / NEMA 1

Adapter (charger)

100-240 Vac, 500 mA switching with plugs for US, EU, GB and AU

Battery

12 VDC / 2.8 Ah Sealed Lead Acid Battery

Lamp

H3, 12 VDC / 100 W

Temperature range

+4 to +40 ºC (+39 to +104 ºF)

Continuous Operation (Max)

10-15 minutes under optimal conditions

Operational range

Up to 4 m (13 ft)

Country of Origin/Intrastatistic Number

EU, 8531 10 30

Shipping dimensions (Lamp box)

310 x 220 x 210 mm (12.725 x 9 x 8.725 ins)

Shipping weight (Lamp)

2.1 kg (4.62 lbs)

Carrying case

Case: polypropylene, Inlay: polyurethane

Shipping dimensions (box)

440 x 340 x 280 mm (17.375 x 13.375 x 11 ins)

Shipping weight incl. test lamp

5 kg (11.1 lbs)

FSL100-TL Battery Specifications

Replacement Part No.

FSL100-TLBT

Battery Type

Rechargeable Sealed Lead-Acid Battery

Battery Voltage And Capacity

12 VDC / 2.7 Ah

Terminal Type

Spade

Dimensions

103 x 70 x 46 mm

FSL100-TLX Hazardous Area Test Lamp Specifications

Housing

Aluminium

Ingress Protection Rating

IP66

Power (Batteries)

6 VDC Nominal (4 X 1.5 VDC AA Alkaline Battery)

Operational Range

Up To 4 M (13 Ft)

Working Temperature Range

-25 To +50 °C (-13 to +122 °F)

Storage Temperature Range

-40 To + 80 °C

Country Of Origin/Intrastatistic Number

EU, 8531 10 30

Shipping Dimensions (Box)

32 X 30 X 13 cm (13 X 11 X 5 in.)

Shipping Weight

3 kg (7 lbs.)

IECEx Certificate

IECEx Zone 1

FSL100-SM21 Swivel Mount

Material Swivel / Bolts and Nuts

PA66 / 316 SS

Weight

280 grams (0.62 lbs)

Table 4. Accessory Specifications

SPECIFICATIONS

Summary of Contents for FSL100-IR3


























































Search results

Summary of Contents for FSL100-IR3

Reviews:

Related manuals for FSL100-IR3

Brands by name

Popular brands

Honeywell FSL100-IR3, Technical Handbook

Search results

Summary of Contents for FSL100-IR3

Reviews:

Related manuals for FSL100-IR3

Brands by name

Popular brands