background image

USA-5

USA

CAN

MEX

D

Pilot lamp set, blue

3

1

2

4

NO

2

NC

1

COM

3

L1

N

NO

2

NC

1

COM

3

L1

N

NC

1

COM

3

NO

NC

2

N

NC

1

COM

3

NO

NO 2

N

110/120 V AC, I = 1.2 mA, 

Order No.: 74916121.

Further information about accessories can be found 
in Technical Information bulletin DG (identical to 
DG..T) – www.docuthek.com

Technical data

Gas type: natural gas, town gas, LPG (gaseous), 
flue gas, biogas (max. 0.1 %-by-vol. H

2

S) and air.

Max. inlet pressure p

max.

 = withstand pressure, 

see page 3 (Adjustment).
Max. test pressure for testing the entire system: tem-
porarily (< 15 minutes) 29 psi (2 bar).
Switching capacity:

U

I (cos φ = 1) I (cos φ = 0.6)

DG..T

max. 240 V AC max. 5 A

max. 0.5 A

DG..TG* < 30 V AC/DC max. 0.1 A max. 0.05 A

* With gold contacts

Maximum medium and ambient temperatures:

-40 to +140°F (-40 to +60°C).

Long-term use in the upper ambient temperature 
range accelerates the ageing of the elastomer ma-
terials and reduces the service life (please contact 
manufacturer).

The set switching point may palpably change in me-

dia and ambient temperatures below -22°F (-30°C).
Storage temperature: -4 to +104°F  
(-20 to +40°C).
Diaphragm pressure switch, silicone-free.
Diaphragm: NBR.
Housing: glass fibre reinforced PBT plastic with 
low gas release.
Lower housing section: AlSi 12.
Enclosure: IP 65. Safety class: 1.
Cable diameter: AWG 24 to AWG 13  
(0.02 to 0.07" (0.5 to 1.8 mm)). 
Line entrance: ½" NPT conduit.
Electrical connection type: screw terminals. 
Max. tightening torque, see Technical Information 
bulletin DG. 
Safety information, see Safety manual DG (identi-
cal to DG..T) – www.docuthek.com.
Weight: 9.5 to 11.3 oz (270 to 320 g). 

Dimensions

1/2" NPT

2.76"

(70 mm)

0.43"

(11 mm)

3"

(76 mm)

Summary of Contents for DG T Series







Reviews: