manualshive.com logo in svg

Honeywell DeltaNet R7515A, Installation Instructions Manual, Page: 8 / 12

Share
Download
Honeywell DeltaNet R7515A Installation Instructions Manual Download Page 8

DELTANET R7515A/B, RP7515A/B, R7516B MICROCEL

™

 CONTROLLERS 

C3384-2 

TO CONNECTOR J9 
IN CONTROLLER 

AK3326 T-TAP 
CABLE ASSEMBLY 
6 FT (1.8M) 

T-TAP CONNECTOR 

8 IN. (200 MM) 

AK3711 
CABLE 
ASSEMBLY 

ELECTRICAL 
JACKET 

YELLOW 

BLACK 

BLUE 

LEAVE OPEN SECTION 
OF ELECTRICAL JACKET 
TO ACT AS STRAIN RELIEF 

CURVED 
SIDE 

PAPER 
MARKER 

SLIT FLAT SIDE 
OF ELECTRICAL 
JACKET (SIDE WITH 
PAPER MARKER) 

RED 

RED 

YELLOW 

BLACK 

BLUE 

PLUG 

Fig. 10. Installing T-Tap Connections to AK3711 Cable Assembly. 

�  

Install four conductors in T-tap connector on AK3326 
T-Tap Cable Assembly as follows: 

a.   Open cover and lay four conductors in slots in 

color-coded base as shown in Figure 11. 

NOTE:   Do not strip insulation from four conductors. 

T-tap connector displaces insulation to 
make electrical connections. 

b.   Snap cover in place over conductors in base. 
c.   To complete individual electrical connections, 

press down each of four connector buttons with 
channel lock pliers. 

d.   Connector buttons should be flush with cover 

when properly secured. 

BUTTONS 

RS-485 

(4) 

C-NAP 

24V AC FROM 
CLASS II POWER 
SOURCE 

COVER 

BASE 

C3506-4 

Fig. 11. Installing Bus Conductors in T-Tap Connector. 

BLUE 

RED

YELLOW

BLACK 

YELLOW

BLACK

BLUE 

RED 

TO 
CONTROLLER 

�  

Connect plug on AK3326 T-Tap Cable Assembly into 
Connector J9 on MicroCel base unit as shown in 
Figure 12. 

CAUTION 

Maximum current rating for the T-Tap Cable Assembly 
is 1.0A (MicroCel is nominally 250 mA). For loads 
greater than 1.0A, hard-wire the system and dedicate 
a transformer for each MicroCel. 

FROM T7515 

FROM AK3711 

SPACE SENSOR 

CABLE ASSEMBLY 

J9 24 VAC C-NAP 
BUS CONNECTOR 

J11 ALTERNATE 
24 VAC SCREW 
TERMINALS 

MOD

W LL 

CNAP 

24 VAC

20

19

15161718 

T2 

T1 

J8 WALL MOD 
CONNECTOR 

J7 ALTERNATE CNAP 
SCREW TERMINALS 

AK3326 T-TAP 
CABLE ASSEMBLY 

SPACE 
SENSOR 
CABLE 
ASSEMBLY 

PLUG 

PLUG  

C3385-2 

CONTROLLER 
BASE INPUT 
BOARD SIDE 

Fig. 12. Installing T-Tap Cable to MicroCel Base Unit. 

95-6083  

8 

Summary of Contents for DeltaNet R7515A













Reviews:

No comments