background image

EN1H-1375GE23 R1014  -  Translation of original

15

Honeywell GmbH

EN

6.11Standby indicator 

The system standby mode has to be registered by the operator or their 
contractors at the responsible authority (most commonly WVU or factory 
inspectorate). Before starting the system, the author has to certify that the 
prerequisites for connection are fulfilled. 
Before the system is connected to the mains power supply, the operator has 
to read the relevant VDE regulations. 
The electrical supply lines must only be installed by companies that are 
authorised to do such work. 

7. Start-up

7.1 Safety instructions for start-up

Inform yourself sufficiently about 
• the equipment of the compact booster unit
• the functionality of the compact booster unit
• the close surroundings of the compact booster unit
• the measures to be taken in an emergency

7.2 Start-up requirements 

Before start-up of the compact booster unit, the following points have to be 
ensured: 
• The compact booster unit has to be connected to all protective equipment 

according to the regulations. 

• The relevant VDE and country-specific regulations have to be adhered to 

and fulfilled.

• The buffer tank has to be full of water. 
• The refilling has to function properly. 
• Flange connections have to be checked if they are fastened tightly. 
• Pipe fittings between pump and pipeline have to be tightened. 
• In and output openings for air-cooling of the motor are free. 
• The precharge pressure of the membrane pressure vessel is checked.
• All shut-off valves in the system are open. 

7.3 Initial operation

The initial start-up should be performed by Honeywell technical staff.

1. Connect electrical circuit on-site. 
2. Main switch set to 

0

 and manual/automatic switch to 

automatic

3. Connect water supply for refilling on-site.
4. Open or loosen the ventilation screws on the pump (refer to operating/ 

assembly instructions). 

5. Slowly open the shut-off valves on the input side and fill the system until 

pump medium runs out of every ventilation borehole.
- To do so, loosen the setting screw to open the refilling valve and fill the 

tank after connecting the system to the water supply. 

- Set the amount of refilling water with the throttle valve. (refer to 

Chapter7.3.1.2). 

6. Close the ventilation screws, tighten pump ventilation lightly. 
7. Set main switch to

 I

8. Set system with manual/automatic switch to 

manual operation

 and 

check in which direction the pump is rotating. 
- The direction of rotation has to be the same as the direction shown by the 

arrow on the motor. If it is rotating in the wrong direction, two phases of 
the inlet have to be exchanged. 

9. Set system with manual/automatic switch to 

automatic operation

.

10. Slowly open the shut-off valve of the output and use the pressure guage 

to check if the system starts if the switch-on pressure is reached (refer to 
Chapter 4.). 
- If the switch-on pressure is set to the wrong value, it has to be changed 

as described in the pressure switch manual. 

11.Slowly close the shut-off valve of the output and use the pressure guage 

to check if the system shuts off when the switch-off pressure is reached  
(refer to Chapter 4.).
- If the switch-off pressure is set to the wrong value, it has to be changed 

as described in the instructions of the pressure switch.

- The follow-up time has to be set on the relay to the maximum number of 

operating cycles that are permissible for the motor by turning the setting 
screw until it reaches a value between 3 and 10 minutes. Up to 7.5kW = 
20 cycles/hour, from 11 to 22kW = 10 cycles /ho, from 30kW = 6 cycles/
hour) 

12.Let the pump run again with the output shut-off valve open, loosen the 

ventilation screw and let the rest of the air out. 

13.Close the ventilation screw tightly. 
14.Check if the pump runs smoothly. 
15.By closing the shut-off valve on the output line, check if the pump 

reaches its maximum pumping head in the zero point. 

Performance of tasks only by qualified personnel (see section 1.11).

Warning

†

Danger from improper operation.

ª

Malfunctions



Before starting, the manual has to be read by the operator as 
well as by the responsible technical/operating personnel and 
has to be stored at the site of the compact booster unit at all 
times.



Adhere to local safety and accident regulations when starting 
the compact booster unit.

†

Damaged or improperly installed compact booster unit.

ª

Malfunctions



Check the compact booster unit for obvious signs of damage; 
eliminate any defects immediately or alert the supervising 
personnel.  The compact booster unit may only be operated in 
perfect working order.

Caution

†

Dry running pump 

ª

Damage to the pump/system! 



If water shortage occurs during start-up, in manual or testing 
mode, the compact booster unit shuts off after approx.  10s. If 
the dry running protection is deactivated, then the operator 
takes responsibility in the case of dry running.

The responsible authorities have to be informed before start-up and be-
fore testing. 

Caution

†

The pipeline is not free of residue 

ª

Danger of damaging the pump/compact booster unit! 



Before start-up (and testing) make sure that pipelines and 
compact booster unit are free of residues. 

Caution

†

No pressure on the output side

ª

Pump starts when main switch is turned on!



During start-up and also during automatic mode, the pump 
starts as soon as the main switch is turned on, because the 
system receives a start command from the pressure switch due 
to the lack of pressure on the output side. This is not even 
prevented if the motor protection switch is also activated. 

The start-up, or testing mode, of the compact booster unit may only be 
initiated if all VDE regulations have been fulfilled. 
Floating ring seals may briefly show signs of leakage during start-up, 
but no longer after a short period of operation. 
The protection against dry running is only active in manual and testing 
modes. 

Summary of Contents for CBU145



























Reviews: