manualshive.com logo in svg

Honeywell AUTOCUBE 8200, User Manual

Share
Download
Honeywell AUTOCUBE 8200 User Manual Download Page 19

AutoCube 8200 User Guide

11

To install the display:

Note:

Depending on your system, the driver for the display may need to be installed from 
the CD provided with it.

1. Attach the USB cable to the display. Use the strain relief on the back of the dis-

play to hold the cable in position.

2. Pull open the side of the display holder, insert the display, then slide the open 

side of the holder back into place over the display.

3. Secure the display by using 2 small screws (provided). On the back of the 

holder, screw them into the holes located in the slots.

4. Adjust the position of the display by loosening the clamp with the knob. Set in 

position and tighten the clamp. Remove the knob, conserving it for future use.

Connect to the Host

1. Connect the display cable(s) exiting the bottom or side of the stand to the host 

PC USB port (s).

2. Turn on the host PC.

3. Carefully remove protective foam from the camera.

If using a display, it is detected by Windows as a second monitor. Set this monitor 
as an extension of Windows desktop in 

Control Panel

, 

Display

, 

Change display 

settings

.

Summary of Contents for AUTOCUBE 8200

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands