background image

Installation and Technical Manual for the

Summing In-Line Amplifier,  

Order Code AA919

Sensing and Internet of Things

Issue A

008-0749-00

m

 WARNING

MISUSE OF DOCUMENTATION

• 

Complete installation, operation, and maintenance 
information is provided in the instructions supplied with 
each product.

• 

Failure to comply with these instructions could result 
in death or serious injury

.

m

 WARNING

PERSONAL INJURY

• 

DO NOT USE these products as safety or emergency 
stop devices or in any other application where failure of 
the product could result in personal injury.

• 

Failure to comply with these instructions could result 
in death or serious injury.

Sensing and Internet of Things

m

 AVERTISSEMENT

MAUVAIS USAGE DE LA 

DOCUMENTATION

• 

Les informations complètes d’installation, d’utilisation 
et d’entretien sont fournies avec les instructions 
accompagnant chaque produit.

• 

L’inobservation de ces instructions risque d’entraîner 
des blessures graves, voire mortelles.

m

 AVERTISSEMENT

PERSONNELS BLESSURES 

CORPORELLES

• 

NE PAS UTILISER ces produits en tant que dispositifs 
d’arrêt d’urgence ou de sécurité, ni dans aucune 
autre application où la défaillance du produit pourrait 
entraîner des personnels blessures corporelles.

• 

L’inobservation de ces instructions risque d’entraîner 
des blessures graves, voire mortelles

.

Summary of Contents for AA919















Reviews: