5898 Wireless DUAL TEC
®
Motion Sensor - Installation Instructions
FR-Canadian
PRELIMINARY DRAFT 5/18/09
-
3 -
1
SELECT MOUNTING LOCATION (See
A
)
Additional guidelines for animal immunity:
•
Mount the center of the sensor at 2.3 m (7.5 feet) high.
•
Set the sensor to the Lowest or Low sensitivity (see step 6a).
•
Install Animal Immune lens (5-532-489-01 - see Lens Change
Instructions on page 3).
•
Install the look-down mask (see Step 6a).
•
Install the sensor where animals cannot come within 1.8 m (6 ft) of
the sensor by climbing on furniture or other objects.
•
Aim the sensor away from stairways, furniture or other objects that
can be climbed on by pets.
•
TEST the installation site to determine the exact level of attainable
animal immunity.
2
REMOVE THE FRONT HOUSING (SEE
B
)
3
SELECT THE RANGE, SENSITIVITY AND PROTOCOL (SEE
C
)
4
CONNECT THE BATTERIES (SEE
D
)
5
REGISTER THE SENSOR TO THE PANEL
Refer to the control panel’s manual and the programming tool manual
for information on registering wireless devices.
Once you enter the sensor serial number into the panel programming,
select the desired loop for that zone.
Serial #
/ LOOP
Serial #1
/ Loop 1
High Sensitivity
No Animal Immunity
Pulse Count 1
Serial #1
/ Loop2
Low Sensitivity / Animal
Immunity [23 kg (50 lb.) / 45
kg (100 lb.)]
Pulse Count 2
Serial #2
/ Loop 1
Low Temperature Trip
When temperature drops
below 7° C ± 2° C
(45° F ± 4° F) for 5 minutes
Low Temp Restoral
When temperature
rises + 2° C
(+ 3° F) above low
temperature trip point
Serial #2
/ Loop 2
High Temperature Trip
When temperature rises
above 35° C ± 2° C
(95° F ± 4° F) for 5 minutes
Low Temp Restoral
When temperature
crops - 2° C
(- 3° F) below high
temperature trip point
6
MOUNT THE SENSOR (SEE
E
)
7
NORMAL WALK TEST– 10 MINUTES
Normal walk test mode activates every time the front cover is closed
and remains active for 10 minutes. For an additional 10 minutes of
walk test time, remove and replace the front cover. In walk test mode,
the LED is always enabled.
Walk through the detection area and observe the LED.
If necessary, adjust the microwave range, pulse count or sensitivity
setting. (For LED activation meaning, refer to the LED Indicator table.)
8
MICROWAVE WALK TEST – 10 MINUTES
1. Set the Microwave Walk Test DIP switch to ON, or toggle it ON and
OFF.
2. Set Range Adjustment potentiometer to 25% and replace the cover.
3. Walk through the detection area and observe the LED.
4. If necessary, adjust the potentiometer until desired detection range
is obtained. (For LED activation meaning, refer to the LED Indicator
table.)
Power Up
Trouble or Anti-Mask
Fast Blinking Red (LED Enabled
or Disabled)
Condition
Indicator LED
Slow Blinking Red (will finish within
60 seconds)
Indicator LEDs
Normal Walk Test
Red ON for 3 seconds if Alarm
Yellow ON for 2 seconds if Microwave
event detected
Green ON for 2 seconds if PIR event
detected
Microwave Walk Test
Red ON if Microwave is set too high
Green ON if Microwave is set correctly
OFF if Microwave is set too low
TROUBLESHOOTING
RED LED flashing rapidly during normal operation indicates a trouble
condition. A microwave, PIR, or temperature compensation fault is
present, or a communication error has occured. Supervision errors
and low battery conditions are indicated at the panel.
Solution:
Momentarily power down the sensor by removing and
replacing all the batteries. If the trouble does not clear, replace the
sensor.
SPECIFICATIONS
Range:
50’ x 60’ (15 m x 18 m) [installed]
35’ x 40’ (11 m x 12 m) [included]
Batteries:
Four 1.5V AA Lithium Batteries (Use only Energizer L91)
Battery Caution: Risk of fire, explosion and burns. Do not
recharge, disassemble, heat above 100° C (212° F), or incinerate.
Dispose of used batteries promptly. Keep away from children.
Microwave Frequency:
24.125 GHz (K-band)
RF Frequency:
345 MHz
PIR White Light Immunity:
6,500 Lux typical
Fluorescent Light Filter:
50 Hz or 60 Hz, switch selectable
Operating Temperature:
-20° to 55° C (-4° to 131° F),
5% - 95% relative humidity (non-condensing)
Self-Tests:
Microwave supervision; End-to-End PIR self-test; Temperature
Compensation
Temperature Compensation:
Advanced Dual Slope
PIR Fields of View:
Wide Angle Lens (P/N 5-532-439-01)
44 long range zones
12 intermediate zones
6 lower zones
4 look-down zones
Animal Immune Lens (P/N 5-532-489-01)
44 long range zones
36 intermediate zones
18 lower zones
4 look-down zones
Dimensions:
4.93” x 2.93” x 1.68” (12.5cm x 7.5cm x 4.3cm)
Weight:
149.0 g (5.26 oz); Packaged: 205.0 g (7.23 oz)
Accessories:
O
ptional Lens Kits -
Long Range Curtain Lens Kit 15 m x 3 m / 50’ x 10’ (P/N DT7000-LRLK)
High Security Lens Kit 11 m x 12 m / 35’ x 40’ (P/N DT7000-HSLK)
Pet Alley Lens Kit 11 m x 12 m / 35’ x 40’ (P/N DT7000-PALK)
Mounting Brackets
–
SMB-10 Swivel Mount Bracket (P/N 0-000-110-01)
SMB-10C Swivel Mount Ceiling Bracket (P/N 0-000-111-01)
Approval Listings:
FCC
IC
CE, C-Tick, cULus Listed
COMPLIANCE NOTES
•
Sensor must be tested once per year.
•
Sensor must have a clear line-of-sight to protected area.
