Activate Garage Door from Control Panel
ACTION
NOTES
1. At the Home or Dashboard screen select the “Automation” icon.
2. At the Automation Screen, select the Garages icon.
3. Select the Garage door that you wish to control/program from the
displayed list. The control advances to the Garage Door operation screen.
4. At the Garage Door operation screen, select the Opened or Closed
Garage Door icon to Close or Open the door.
5. The SSA1 Siren sounds and the strobe flashes before garage door
operation begins. Siren operation ceases after approximately 5 seconds
but the strobe continues flashing until the garage door position changes or
after 1 minute if the door status does not change.
6. When the door position has changed the icon will switch from Opened to
Closed, as applicable, and CLOSED or OPENED is displayed.
•
When the garage door is open, “Ready to Arm
– Fault” is displayed in a yellow band at the top
of the display.
•
If a “Close in” or “Close at” time has been
programmed, the garage door will always
operate as programmed until the selection has
been cleared.
•
The SSA1 Siren & Strobe will only operate
when the opener is activated remotely or
automatically (via the Close in or Close at
feature) from the Control Panel, or using
TotalConnect.
Program the “Close in” feature at the Control Panel
(LYNX Touch and Lyric Controller only)
ACTION
NOTES
1. At the Home or Dashboard screen select the “Automation” icon.
2. At the Automation Screen, select the Garages icon.
3. Select the Garage door that you wish to program from the displayed list.
The control advances to the Garage Door operation screen.
4. Select the “Close in” tab at the bottom of the screen.
5. On the displayed keypad, enter a desired 4-digit period of time (hh:mm)
that the door will remain open before automatically closing (up to 12
hours, 59 minutes).
6. Select “Done.”
7. The panel returns to the Garage Door operation screen and the “Close in”
time is displayed in the tab.
•
The maximum period of time that can be
programmed for the “Close in” feature is 12
hours and 59 minutes.
•
If a “Close in” time has been programmed, the
garage
door
will
always
operate
as
programmed until the selection has been
cleared.
Program the “Close at” feature at the Control Panel
(LYNX Touch and Lyric Controller only)
ACTION
NOTES
1. At the Home or Dashboard screen select the “Automation” icon.
2. At the Automation Screen, select the Garages icon.
3. Select the Garage door that you wish to program from the displayed list.
The control advances to the Garage Door operation screen.
4. Select the “Close at” tab at the bottom of the screen.
5. On the displayed keypad, enter a desired 4-digit time (hh:mm) that the
door automatically close if it has been left open.
6. Select the AM/PM button to toggle between the options.
7. Select “Done.”
8. The panel returns to the Garage Door operation screen and the “Close at”
time is displayed in the tab.
•
If a “Close at” time has been programmed, the
garage
door
will
always
operate
as
programmed until the selection has been
cleared.
Clearing the “Close at” or “Close in” programs at the Control Panel
(LYNX Touch and Lyric Controller only)
ACTION
NOTES
1. At the Home or Dashboard screen select the “Automation” icon.
2. At the Automation Screen, select the Garages icon.
3. Select the Garage door that you wish to program from the displayed list.
The control advances to the Garage Door operation screen.
4. Select the “Close in” or “Close at” tab at the bottom of the screen.
5. Select the “Clear” button then select “Done.”
6. The panel returns to the Garage Door operation screen and the “Close in”
or “Close at” time is removed from the tab.
•
If a “Close in” or “Close at” time has been
programmed, the garage door will always
operate as programmed until the selection has
been cleared.
