background image

Additional Features: Bolt-Down Kit

Additional Features: Bolt-Down Kit

Additional Features: Bolt-Down Kit

Additional Features: Bolt-Down Kit

Additional Features: Bolt-Down Kit

Installation Procedure

Installation Procedure

Installation Procedure

Installation Procedure

Installation Procedure

1. Choose a mounting location that is easily

accessible from both above and below.

2. Carefully position the template on the location

that you want to mount the safe.

3. Create the guide marks by pressing a sharp

tool through the circles at the four corners of

the template and into the mounting location.

4. Drill a hole (the diameter of the break-off bolt

shaft) through each guide mark.

5. Before attaching the safe, you should check

carefully that the 4 holes you have drilled

match up precisely with the holes that have

been pre-drilled in the bottom of the safe.

Note: 

On certain models, It may be necessary

to remove the rubber foot pads that are

screwed into the bolt-down holes at the

factory.

6. Once you have confirmed that the holes are

aligned and in the location you desire, install

the break-off bolts and washers from

underneath the mounting location (through

the furniture or shelf), and into the pre-drilled

holes in the safe.

7. Turn bolts until the screw heads break off.

Home and Office Security Safes

Models 2054D (only)

Models 2054D (only)

Models 2054D (only)

Models 2054D (only)

Models 2054D (only)

7

77

77

Important: 

Important: 

Important: 

Important: 

Important:  DON’T DRILL SAFE

DON’T DRILL SAFE

DON’T DRILL SAFE

DON’T DRILL SAFE

DON’T DRILL SAFE

Do not drill into the feet, bottom or

any other part of safe!  Doing so will

ELIMINATE THE FIRE PROTECTION

ELIMINATE THE FIRE PROTECTION

ELIMINATE THE FIRE PROTECTION

ELIMINATE THE FIRE PROTECTION

ELIMINATE THE FIRE PROTECTION

that has been designed into your safe

and invalidate all stated warranties.

Installing Your Safe

Installing Your Safe

Installing Your Safe

Installing Your Safe

Installing Your Safe

Certain models include a Bolt-Down kit with break-off bolts and a mounting

template for permanent mounting to a flat surface. Once the safe is installed

using the break-off bolts, it is permanent and cannot be easily removed.

Tools Required

Tools Required

Tools Required

Tools Required

Tools Required

4 – Break-off Bolts (Supplied)

4 – Washers(Supplied)

1 – Mounting Template (Supplied)

1 – Drill

1 – Screwdriver

6

66

66

Additional Features: Bolt-Down Kit

Additional Features: Bolt-Down Kit

Additional Features: Bolt-Down Kit

Additional Features: Bolt-Down Kit

Additional Features: Bolt-Down Kit

Models 2054D (only)

Models 2054D (only)

Models 2054D (only)

Models 2054D (only)

Models 2054D (only)

Important: 

Important: 

Important: 

Important: 

Important:  SECURING TO FLOOR

SECURING TO FLOOR

SECURING TO FLOOR

SECURING TO FLOOR

SECURING TO FLOOR

Many consumers prefer to bolt their safe to the floor to

increase protection from theft and resistance to tipping. If

your safe was manufactured with bolt down holes pre-

drilled in the floor of the safe, bolting your safe to the

floor may provide additional theft deterrence.
If you have 

ANY QUESTIONS

ANY QUESTIONS

ANY QUESTIONS

ANY QUESTIONS

ANY QUESTIONS     

about how to accomplish

this, or are uncomfortable using the tools necessary to

complete this project, please check with your local retailer,

home center, or independent contractor.

Summary of Contents for 2054D















Reviews: