background image

16

AIR INDEX

An Air Index Information hang tag/label is applied to engines certified 
to an emission durability time period in accordance with the 
requirements of the California Air Resources Board.
The bar graph is intended to provide you, our customer, the ability to 
compare the emissions performance of available engines. The lower 
the Air Index, the less pollution.
The durability description is intended to provide you with information 
relating the engine’s emission durability period. The descriptive term 
indicates the useful life period for the engine’s emission control 
system. See your 

EMISSION CONTROL SYSTEM WARRANTY

 

(page 19) for additional information

.

The Air Index Information hang tag/label must remain on the lawn 
mower until it is sold. Remove the hang tag before operating the lawn 
mower.

SPECIFICATIONS

Mower Model

Maintenance

Transmission Design and Performance

Tuneup

Dimensions, Weights and Capacities

Engine Design and Performance 

Descriptive Term

Applicable to Emissions

Durability Period

Moderate

 50 hours (0–80 cc inclusive)

125 hours (greater than 80 cc)

Intermediate

125 hours (0–80 cc inclusive)
250 hours (greater than 80 cc)

Extended

300 hours (0–80 cc inclusive)
500 hours (greater than 80 cc)

1000 hours (225 cc and greater)

HRR216VXA

Honda rotary mower, grass bag, 
variable speed transmission,
21 inch mower deck

Fuel

Unleaded gasoline with a pump 

octane rating of 86 or higher

page 12

Engine Oil

SAE 10W-30, API SJ or later

* Refill amount: 12.0 ~ 13.5 oz

(0.35 ~ 0.40 

)

page 10

Spark Plug 
Type

Regular

: NGK- BP6ES or

DENSO: W20EP-U

Resistor

: NGK - BPR6ES or

DENSO - W20EPR-U

page 11

Maximum 
Governed 
Speed

2,950 ~ 3,100 rpm

Shop 
manual

Smart Drive 
Cable

Adjust for proper operation.

**

Throttle Cable

Adjust for proper choke operation and 

maximum governed speed.

Shop 
manual

Blade Bolt 
Torque

36 ~ 43 ft-lb

(49 ~ 59 N•m)

page 9

* Approximate value. Actual amount will vary due to residual oil 
remaining in the engine. Always check the level using the dipstick 
(see page 10).

** See the FAQ section of the Honda Power Equipment web site. 
Visit www.hondapowerequipment.com/faq.htm

Transmission Type

Variable speed 

Thumb or hand operation (twist grip)

Maximum Mower 
Ground Speed 
(engine at 3,100 rpm)

0 ~ 3.8 mph 

(0 ~ 6.1 km/h)

Spark Plug Gap

0.028 ~ 0.031 in 

(0.7 ~ 0.8 mm)

page 11

Idle Speed
(throttle lever at SLOW)

1,700 ± 150 rpm

Shop 
manual

Valve Clearance (cold)

Intake: 0.15 ± 0.04 mm

Exhaust: 0.20 ± 0.04 mm

Shop 
manual

Other Specifications

No other adjustments needed.

Overall Length

63.0 in (1600 mm)

Width at Mower Deck

23 in (585 mm)

Overall Height

40.4 in (1027 mm) 

Dry Weight

97.2 lb (44.1 kg) 

Wheelbase

24.8 in (630 mm)

Cutting Width

21 in (530 mm)

Approximate Cutting 
Height 
(7 adjustable positions)

3/4 ~ 4 in 

(20 ~ 100 mm)

Fuel Tank Capacity

0.25 US gal (0.93 

l

)

Engine Oil Capacity

0.58 US qt (0.55 

l

)

Engine Model

GCV160

Engine Type

4-stroke, overhead-cam, single-cylinder, 

forced air-cooled

Displacement

9.8 cu in 

(160 cc)

Bore and Stroke

2.52 x 1.97 in 

(64 x 50 mm)

Compression Ratio

8.5:1

Ignition System

Transistorized magneto

Net Power

4.4 hp (3.3 kW)

Net Maximum Torque

6.9 ft-lb (9.4 N•m) 

Summary of Contents for HRR216VXA

























Reviews: