background image

11

1. Press down on the cover tabs and remove the cover.

2. Remove the filter from the air cleaner housing. 

3. Inspect the filter, and replace it if damaged.

4. Clean the filter by tapping it several times on a hard surface to 

remove dirt, or blow compressed air (not exceeding 30 psi
[207 kPa]) through the filter from the inside. Never try to brush off 
dirt; brushing will force dirt into the fibers.

5. Wipe dirt from the inside of the air cleaner housing and cover, 

using a moist rag. Be careful to prevent dirt from entering the air 
duct that leads to the carburetor.

6. Reinstall the filter and cover.

Spark Plug Service

*Resistor spark plugs reduce interference with radio and 
TV reception.

NOTICE

Incorrect spark plugs can cause engine damage.

For good performance, the spark plug must be properly gapped and 
free of deposits.

1. Disconnect the spark 

plug cap and remove 
any dirt from around the 
spark plug area.

2. Remove the spark plug 

with a 13/16 in (21 mm) 
spark plug wrench. 

3. Inspect the spark plug. 

Replace it if the 
electrodes are worn, or if 
the insulator is cracked 
or chipped.

4. Measure the spark plug 

electrode gap with a suitable 
gauge. The gap should be 
0.028 ~ 0.031 in (0.7 ~ 0.8 
mm). Correct the gap, if 
necessary, by carefully 
bending the side electrode.

5. Install the spark plug 

carefully, by hand, to avoid 
cross-threading.

6. After the spark plug seats, tighten with a 13/16 in (21 mm) spark 

plug wrench to compress the washer.

If reinstalling the old spark plug, tighten 1/8 to 1/4 turn after the 
spark plug seats.

If installing a new spark plug, tighten 1/2 turn after the spark plug 
seats to compress the sealing washer.

NOTICE

A loose spark plug can overheat and damage the engine. 
Overtightening the spark plug can damage the threads in the 
cylinder head.

7. Install the spark plug cap on the spark plug.

Spark Arrester Service (optional equipment)

Your lawn mower engine is not factory-equipped with a spark arrester. 
In some areas it is illegal to operate an engine without a spark 
arrester. Check local laws and regulations. In optional USDA 
approved spark arrester is available from an authorized Honda 
servicing dealer (see page 17).

RECOMMENDED SPARK PLUGS

REGULAR

RESISTOR*

NGK

BP6ES

BPR6ES

DENSO

W20EP-U

W20EPR-U

AIR CLEANER 
HOUSING

FILTER

COVER

COVER TABS

SPARK PLUG

SPARK 
PLUG CAP

SPARK PLUG WRENCH

0.028 ~ 0.031 in

(0.7 ~ 0.8 mm)

SEALING
WASHER

Summary of Contents for HRR216VXA

























Reviews: