background image

10

GRASS BAG

Inspection

During normal use, the grass bag material is subject to deterioration 
and wear.

NOTICE

Frequently inspect the grass bag for tears, holes, and excessive wear. 
Check for necessary replacement. Make sure the new bag meets the 
original specification.

Cleaning

Wash the bag with a garden hose, and allow it to dry completely 
before use; a wet bag will clog quickly.

Replacement

Replace a worn or damaged bag with a Honda replacement bag or its 
equivalent (page 17).

Removal

1. Unclip the plastic edges of 

the bag from the frame.

2. Remove the frame from 

the bag.

Installation

1. Insert the frame into the 

bag, as shown.

2. Clip the plastic edges of 

the bag onto the frame, as 
shown.

ENGINE MAINTENANCE

Engine Oil Level Check

1. Unscrew and remove the 

filler cap/dipstick and 
wipe it clean.

2. Insert and remove the 

dipstick 

without 

screwing it into the 
filler neck

. Check the oil 

level shown on the 
dipstick.

3. If the oil level is low, add 

oil to reach the upper 
limit mark on the dipstick. 
Do not overfill. If the 
engine is overfilled, the 
excess oil may get 
transferred to the air 
cleaner housing and air 
cleaner filter.

NOTICE

Running the engine with a low oil level can cause engine damage. 
This type of damage is not covered by the 

DISTRIBUTOR’S 

LIMITED WARRANTY (

page 18)

.

4. Screw in the filler cap/dipstick securely.

Engine Oil 
Recommendations

Oil is a major factor affecting 
performance and service life. 
Use 4-stroke automotive 
detergent oil.

Always change the oil in 
accordance with the 

MAINTENANCE SCHEDULE

 (page 8).

SAE 10W-30 is recommended for general use. Other viscosities 
shown in the chart may be used when the average temperature in 
your area is within the recommended range.

The SAE oil viscosity and service classification are in the API label on 
the oil container. Honda recommends API SERVICE category SJ or 
later oil with the ILSAC “starburst” certification mark.

Engine Oil Change

Drain the used oil while the engine is warm. Warm oil drains quickly 
and completely.

1. Turn the fuel valve OFF. This will reduce the possibility of fuel 

leakage.

2. Wipe the oil filler area clean, then remove the oil filler cap/dipstick.

3. Place a suitable 

container next to the 
mower to catch the 
used oil, then tilt the 
mower on its right 
side.

The used oil will drain 
through the filler neck. 
Allow the oil to drain 
completely.

Please dispose of used motor oil and the containers in a manner 
that is compatible with the environment. We suggest you take it in 
a sealed container to your local recycling center or service station 
for reclamation. Do not throw it in the trash, pour it on the ground, 
or pour it down a drain.

4. Fill with the recommended oil. 

Do not overfill. Allow a couple 
of minutes for the oil to settle 
in the engine, then measure 
the oil level as shown.

NOTICE

Using nondetergent oil can 
shorten the engine’s service 
life, and using 2-stroke oil can 
damage the engine.

Air Cleaner Service

A dirty air cleaner will restrict air flow to the carburetor, reducing 
engine performance. If you operate the mower in very dusty areas, 
clean the air cleaner more often than specified in the 

MAINTENANCE 

SCHEDULE

 (page 8).

NOTICE

Operating the engine without an air cleaner or with a damaged air 
cleaner will allow dirt to enter the engine, causing rapid engine wear. 
This type of damage is not covered by the 

DISTRIBUTOR’S LIMITED 

WARRANTY 

(page 18).

FRAME

PLASTIC EDGE

BAG

PLASTIC 
EDGE

FILLER 
CAP/DIPSTICK 
(Do not screw 
in the dipstick 
when checking 
oil level)

UPPER 
LIMIT

LOWER 
LIMIT

Summary of Contents for HRR216VXA

























Reviews: