background image

Insert this frame into the
canvas cover, ensuring that
it is correctly positioned
along the base perimeter.

Hook all the plastic profiles
to the frame tubes with the
help of a screwdriver (7).

Insert the handle (8) with the grommets (14) into the holes of the can-
vas (9) making sure that the end with the lump  (15) is on the right.
Attach this to the frame using the screws (10), following the  in di ca -
ted sequence, and complete the assembly scre wing the four front
and rear self-thread ing screws (11).

Position the grommets (14) in their respective holes in the canvas
(9).
Lastly, fit the stiffening bar (12) on the outside of the frame base,
keeping the flat part towards the canvas and using the nuts and
screws supplied (13) in the sequence indicated.

CONNECTING THE BATTERY

The battery (1) is situated
in a compartment under
the steering wheel and is
reached by removing the
plastic cover (2) held on by
two screws (3).

Connect the two red cables
(4) to the positive terminal
(+) and the two black ca-
bles (5) to the negative ter-
minal (–) using the supplied
screws and following the il-
lustra ted sequence.

Recharge the battery according to the manufacturer's instructions.

To prevent the safety device in the electronics

card from cutting in, never start the engine until the battery is  fully
charged!

Follow the battery manufacturer's instruc-

tions regarding safe handling and disposal.

FITTING THE GRASS-CATCHER

First of all assemble the frame, joining the upper part (1), including
the opening, to the lower part (2), using the supplied nuts and
screws (3) and following the indicated sequence.

Position the angle supports (4) and (5), respecting the right (R ) and
left (L

) sides, and attach them to the frame using the four

self-tapping screws (6).

IMPORTANT

WARNING!

5 EN

CLAK

7

Summary of Contents for HF1211



























Reviews: