Honda EU3200i Owner'S Manual Download Page 43 | Manualshive

Page: 43 / 100

background image

OPERATION

41

STOPPING THE ENGINE with

Bluetooth

® ENABLED SMARTPHONE

The engine can be stopped via a

Bluetooth

® enabled smartphone using a

Bluetooth

® application.

Refer to the

Bluetooth

® application to check the connection, operation, and for

help pairing a smartphone.

HOW TO RESTART WHEN STOPPED BY CO-MINDER® (CO SHUT-OFF SYSTEM)

When the engine is automatically stopped by the CO-MINDER®, move the
generator to an area with fresh air and away from any device that may be
emitting carbon monoxide, such as another generator. Press the CO-MINDER®
reset button and then follow the standard procedure for starting the engine.
When the CO ALARM indicator or the FAULT/CO-MINDER® LIFE indicator flashes,
press the CO-MINDER® reset button to turn off the indicator.

• After the engine is stopped by the CO-MINDER® (CO Shut-off System), the engine

cannot be restarted for approximately 30 seconds.

CO-MINDER® RESET BUTTON

CO ALARM INDICATOR

FAULT/CO SENSOR LIFE
INDICATOR

«
...
41
42
43
44
45
...
»

Summary of Contents for EU3200i





































































































Reviews:

No comments

Related manuals for EU3200i

Brand: Bang & Olufsen Pages: 213

Brand: GENMAX Pages: 28

Brand: Predator Pages: 24

Brand: Daewoo Pages: 91

Brand: Panacom Pages: 10

Brand: Roberts Pages: 12

MagicMount MAGPBEZ

Brand: Scosche Pages: 4

Brand: Muse Pages: 14

Hard Gear SGE3500BSi

Brand: DAISHIN Pages: 28

GO Groove Audio Morph

Brand: Accessory Power Pages: 8

Brand: Fenton Pages: 16

Flexfiller 125D

Brand: flamco Pages: 44

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 1

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands