Honda EU2200i Owner'S Manual Download Page 62

Page: 62 / 104

SERVICING YOUR GENERATOR

AIR CLEANER SERVICE

Main and Outer Filters Cleaning

Dirty air filters will restrict air flow to the carburetor, reducing engine
performance. If you operate the generator in very dusty areas, clean the main
and outer filters more frequently than specified in the Maintenance Schedule.

1. Clean the air filters in warm soapy water, rinse, and allow to dry thoroughly, or

clean in nonflammable solvent and allow to dry.

2. Dip the air cleaner element in clean engine oil, and then squeeze out all

excess oil. The engine will smoke when started if too much oil is left in the air
filters.

3. Wipe dirt from the air cleaner housing and cover using a moist rag.

Be careful to prevent dirt from entering the air duct that leads to the
carburetor.

Clean

Squeeze and dry

Dip in oil

Squeeze

Do not twist.

31Z446100.book 60 ページ２０２０年２月１７日　月曜日　午前１１時４１分

Summary of Contents for EU2200i









































































































Search results

Summary of Contents for EU2200i

Reviews:

Related manuals for EU2200i

Brands by name

Popular brands

Honda EU2200i, Owner'S Manual

Search results

Summary of Contents for EU2200i

Reviews:

Related manuals for EU2200i

Brands by name

Popular brands