manualshive.com logo in svg

Honda EG5000X, Owner'S Manual

Share
Download
Honda EG5000X Owner'S Manual Download Page 24

22

REFUELING

Gasoline is highly flammable and explosive.

You can be burned or seriously injured when handling fuel.

Stop the engine and keep heat, sparks, and flame away.
Handle fuel only outdoors.
Wipe up spills immediately.

FUEL TANK CAP

TETHER
(CALIFORNIA TYPE)

UPPER LIMIT MARK

With the engine stopped, remove the fuel tank cap and check the fuel
level. Refill the fuel tank if the fuel level is low.

Fuel can damage paint and plastic. Be careful not to spill fuel when
filling your fuel tank. Damage caused by spilled fuel is not covered
under warranty.

Spilled fuel is not only a fire hazard, it causes environmental damage.
Wipe up spills immediately.

Never refuel the engine inside a building where gasoline fumes may
reach flames or sparks. Keep gasoline away from appliance pilot
lights, barbecues, electric appliances, power tools, etc.

After refueling, reinstall the fuel tank cap securely.

Refuel in a well-ventilated area with the engine stopped. If the engine
has been running, allow it to cool first. Refuel carefully to avoid
spilling fuel. Do not fill above the upper limit mark.

09/03/03 15:47:11 31ZC2770_023

Summary of Contents for EG5000X
























































Reviews:

No comments

Brands by name

Popular brands

Load more brands