manualshive.com logo in svg

Honda EB2200i, Owner'S Manual

Share
Download
Honda EB2200i Owner'S Manual Download Page 83

81

INITIAL USE INSTRUCTIONS

2. Add fuel carefully to avoid spilling fuel. Do not fill the fuel tank 

above the upper level mark (red) on the fuel filter.

Fuel can damage paint and plastic. Be careful not to spill fuel when 
filling your fuel tank. Damage caused by spilled fuel is not covered 
under the 

Distributor’s Limited Warranty.

3. After refueling, tighten the fuel filler cap until it clicks. Keep the fuel 

filler cap vent lever OFF for storage or transport, and ON to run the 
generator.

Move the generator at least 10 feet (3 meters) away from the fueling 
source and site before starting the engine.

After initial fueling (or anytime the generator is run completely out of 
fuel), starting the engine may require additional pulls of the starter 
grip. This generator utilizes a vacuum operated fuel pump and may 
require additional pulls to draw fuel into the carburetor.

UPPER LEVEL MARK (RED)

TETHER

FUEL FILTER

FUEL FILLER CAP VENT LEVER

OFF

ON

FUEL FILLER CAP

31Z448020.book  81 ページ  ２０１９年２月８日　金曜日　午前９時１６分

Summary of Contents for EB2200i





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands