manualshive.com logo in svg

Honda EB2200i, Owner'S Manual

Share
Download
Honda EB2200i Owner'S Manual Download Page 82

80

INITIAL USE INSTRUCTIONS

FUEL

Add fuel to the generator in a well-ventilated area. Never refuel the 
engine inside a building where gasoline fumes may reach flames or 
sparks. Keep gasoline away from appliance pilot lights, barbecues, 
electric appliances, power tools, etc. Spilled fuel is not only a fire 
hazard, it causes environmental damage. Wipe up spills immediately.

This engine is certified to operate on unleaded gasoline with a pump 
octane rating of 86 or higher. Refer to page 39 for additional fuel 
recommendations.

1. Remove the fuel filler cap.

Gasoline is highly flammable and 
explosive.

You can be burned or seriously 
injured when handling fuel.

• Stop the engine and let it cool 

before handling fuel.

• Keep heat, sparks, and flame away.
• Handle fuel only outdoors.
• Wipe up spills immediately.

FUEL FILLER CAP

31Z448020.book  80 ページ  ２０１９年２月８日　金曜日　午前９時１６分

Summary of Contents for EB2200i





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands