manualshive.com logo in svg

Honda EB2200i, Owner'S Manual

Share
Download
Honda EB2200i Owner'S Manual Download Page 81

79

INITIAL USE INSTRUCTIONS

ENGINE OIL

The generator is shipped 

WITHOUT OIL

 in the engine.

1. Place the generator on a level surface.

2. Loosen the maintenance cover screw and remove the maintenance 

cover.

3. With the generator in a level position, remove the oil filler cap.

4. Add enough SAE 10W-30 API service category SJ or later (or 

equivalent) oil to bring the oil level to the upper limit of the oil filler 
neck. SAE 10W-30 oil is recommended for general use; for 
additional recommendations, see page 42.

Maximum oil capacity: 

14 oz (0.44 L)

Do not overfill the engine with oil.

 If the engine is overfilled, the 

excess oil may be transferred to the air cleaner case and air filters.

5. Screw in the oil filler cap securely.

6. Reinstall the maintenance cover and tighten the maintenance cover 

screw securely.

MAINTENANCE 
COVER SCREW

MAINTENANCE COVER

OIL FILLER CAP

UPPER LIMIT

OIL FILLER NECK

LOWER LIMIT

31Z448020.book  79 ページ  ２０１９年２月８日　金曜日　午前９時１６分

Summary of Contents for EB2200i





























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands