manualshive.com logo in svg

Honda DREAM YUGA, Owner'S Manual

Share
Download
Honda DREAM YUGA Owner'S Manual Download Page 65

Honda Motorcycle & Scooter India Pvt. Ltd.

57

(1)

2.  Swing arm bearings - this can be checked  

by pushing hard against the side of 

 

the rear wheel while the vehicle is 

 

on a Center stand. Freeplay indicates 

worn bearings.

3. Carefully inspect all front and rear 

 

suspension fasteners for tightness.

SIDE STAND

Refer to the Safety Precautions on 

page 37.

Check the side stand spring (1) for damage 

and loss of tension, and the side stand 

 

assembly for freedom of movement.

(1) Side stand spring 

¼lkbM LVSUM fLizax½

If the side stand is squeaky or stiff, clean 

the pivot area and lubricate the 

pivot bolt 

with clean engine oil.

WHEEL REMOVAL

Refer to the Saf

ety Precautions on 

page 37

.

Front Wheel Removal

1.  Place the vehicle on its center stand.
2.  Raise the front wheel off the ground 

by placing a support block under the 

engine.

3.  Remove the speedometer cable (1) by 

pushing the tab (2).

4.  Remove the front brake adjusting nut 

(3) and remove the front brake cable 

(4) from the brake arm (5). 

5.  Remove the front axle nut (6).
6.  Remove the front axle shaft (7) and the 

wheel.

Summary of Contents for DREAM YUGA






























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands