manualshive.com logo in svg

Honda DREAM YUGA, Owner'S Manual

Share
Download
Honda DREAM YUGA Owner'S Manual Download Page 63

Honda Motorcycle & Scooter India Pvt. Ltd.

55

Improper maintenance of chain can lead 

to premature wear of sprockets and chain 

drive.

of adjustment, the drive chain is worn and 

must be replaced.

5.  Tighten the sleeve nut to:
 

44 N.m (4.5 kgf.m, 32 lbf.ft)

 

Tighten the rear axle nut:

 

54 N.m (5.9 kgf.m, 43 lbf.ft)

If the torque wrench is not used for this 

installation, see your Honda dealer as soon 

as possible to verify proper  assembly.

6.  Tighten the adjusting nuts lightly, then 

tighten the lock nuts by holding the 

adjusting nuts with a spanner.

7.  Recheck drive chain slack.
8.  Rear brake pedal freeplay is affected 

when repositioning the rear wheel to 

adjust drive chain slack. Check rear 

brake pedal freeplay and adjust as 

necessary (page 15).

Lubrication and Cleaning:

Lubri

cate every 1000 km (600 miles) or 

sooner if chain appears dry. 

To clean and lubricate the chain visit your 

nearest Honda Dealer/Service Center.

 

Replacment chain: 420AD-118

 NOTICE

Removal and Cleaning:

When the drive chain becomes dirty, it 

should be removed and cleaned prior to 

lubrication.
1.  With the engine off, Remove the drive 

chain cases  and carefully remove the 

master link retaining clip (1) with a pair 

of pliers. Do not bend or twist the clip. 

Remove the master link. Remove the 

drive chain from the vehicle. 

2.  Clean the drive chain in high flash-point 

solvent and allow it to dry. Inspect the 

Summary of Contents for DREAM YUGA






























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands