manualshive.com logo in svg

Honda BF250A, Owner'S Manual, Page: 72 / 139

Share
Download
Honda BF250A Owner'S Manual Download Page 72

70

SERVICING YOUR OUTBOARD MOTOR

Spark Plug Service

<Standard Spark Plug>

RECOMMENDED SPARK PLUGS:

ZFR6K-11E (NGK)

Incorrect spark plugs can cause 

engine damage.

See page 73 for instructions of 

handling the Iridium spark plugs 

(optional parts).

1. Disconnect the battery negative (–) 

terminal.

2. Unlock and remove the engine 

cover (p. 63).

3. Remove the 6 × 22 mm special bolt 

and remove the plug maintenance 

cover.

4. Disconnect the wire connector 

from the ignition coil by pushing 

on the lock tab and pulling on the 

connector. Pull on the plastic 

connector, not the wires.

5. Remove the bolt with a 10 mm 

wrench. Remove the ignition coil 

by pulling it up slightly.

Do not strike or drop the ignition coil, 

or it may be damaged and require 

replacement.

6 × 22 mm 

SPECIAL BOLT

PLUG MAINTENANCE COVER

WIRE CONNECTOR

BOLT

IGNITION COIL

31ZX26040.book  Page 70  Friday, July 25, 2014  5:14 PM

Summary of Contents for BF250A












































































































































Reviews:

No comments