manualshive.com logo in svg

Honda BF250A, Owner'S Manual, Page: 26 / 139

Share
Download
Honda BF250A Owner'S Manual Download Page 26

24

CONTROLS AND FEATURES

Gearshift/Throttle Control 

Lever

The gearshift/throttle control lever(s) 

controls engine speed and selects F 

(forward), N (neutral), or R (reverse) 

gears.

Moving the control lever 35° from N 

(neutral) selects the gear, and further 

movement increases engine speed.

A friction adjuster inside the control 

box adjusts the operating resistance 

of the control lever(s). Refer to p. 51.

Less friction allows easier control 

lever movement. More friction helps 

to hold a steady throttle setting while 

cruising.

SINGLE TYPE

GEARSHIFT/

THROTTLE

CONTROL

LEVER

DUAL TYPE

GEARSHIFT/THROTTLE

CONTROL LEVERS

MAXIMUM

SHIFT

F (FORWARD)

35°

N (NEUTRAL)

R (REVERSE)

GEARSHIFT/THROTTLE

CONTROL LEVER

THROTTLE OPENING

MINIMUM

THROTTLE OPENING

MINIMUM

SHIFT

35°

MAXIMUM

31ZX26040.book  Page 24  Friday, July 25, 2014  5:14 PM

Summary of Contents for BF250A












































































































































Reviews:

No comments