manualshive.com logo in svg

Honda BF250A, Owner'S Manual, Page: 70 / 139

Share
Download
Honda BF250A Owner'S Manual Download Page 70

68

SERVICING YOUR OUTBOARD MOTOR

7. Start the engine and check for 

leaks.

Running the engine without water 

can cause serious engine damage. 

If you are changing the oil filter 

while the outboard motor is out of 

the water, use commercially 

available Ear-muffs and a hose to 

supply water.

8. Stop the engine, and check the oil 

level as described on page 64. If 

necessary, add oil to bring the oil 

level to the upper limit mark on the 

dipstick.

Engine Oil Recommendations

Oil is a major factor affecting 

performance and service life. Use 

4-stroke detergent oil.

Honda 10W-30 FC-W

®

 outboard 

motor oil is recommended for general 

use.

FC-W

®

 is a registered trademark of 

the National Marine Manufacturers 

Association.

If Honda 10W-30 FC-W oil is not 

available, Honda recommends that 

you use API service category SG, SH 

or SJ oil. The SAE oil viscosity and 

service category are in the API label 

on the oil container.

AMBIENT TEMPERATURE

31ZX26040.book  Page 68  Friday, July 25, 2014  5:14 PM

Summary of Contents for BF250A












































































































































Reviews:

No comments