Honda 2012 NC700D Owner'S Manual Download Page 29

Page: 29 / 130

n Gu

Parking Brake

Parking Brake Lever

Be sure the parking brake is applied while
parking and warming up the engine.

Make sure the parking brake lever is released
before riding.

To apply the parking brake
Squeeze the rear brake lever and pull the
parking brake lever back to lock the rear
wheel.

The parking brake lock will not function if
the parking brake is not adjusted properly.

(P76)

To release the parking brake
Release the parking brake lever by lightly
pulling in the lever.

Before riding, check that the parking brake
indicator is turned off and make sure that the
parking brake is fully released so there is no
drag on the rear wheel.

Pull

Apply

Release

Lightly pull

Squeeze

Release

Parking brake lever

12 NC700D (NM-2)(TH)-32MGS8000.book 26 ページ２０１２年４月１８日　水曜日　午後９時３分

Summary of Contents for 2012 NC700D



































































































































Search results

Summary of Contents for 2012 NC700D

Reviews:

Related manuals for 2012 NC700D

Brands by name

Popular brands

Honda 2012 NC700D, Owner'S Manual

Search results

Summary of Contents for 2012 NC700D

Reviews:

Related manuals for 2012 NC700D

Brands by name

Popular brands