Honda 2012 NC700D Owner'S Manual Download Page 37

Page: 37 / 130

n Gu

Refuelling

Fuel type:

Unleaded petrol only

Fuel octane number:

Your motorcycle is

designed to use Research Octane Number
(RON) 91 or higher.

Tank capacity:

14.1 litres (3.73 US gal,

3.10 Imp gal)

❙

Refuelling and Fuel Guideline

(P10)

Opening the Fuel Fill Cap

Open the seat.

(P35)

Turn the fuel fill cap counterclockwise until
it stops and remove the cap.

Closing the Fuel Fill Cap

Install and tighten the fuel fill cap firmly by
turning it clockwise.

Make sure that the arrow marks on the
cap and fuel tank are aligned.

Close the seat.

Do not fill with fuel above the plate.

WARNING

Petrol is highly flammable and
explosive. You can be burned or
seriously injured when handling fuel.

•

Stop the engine, and keep heat,
sparks, and flame away.

•

Handle fuel only outdoors.

•

Wipe up spills immediately.

Filler neck plate
Fuel level (max)

Arrow marks

Fuel fill cap

Fuel filler opening

12 NC700D (NM-2)(TH)-32MGS8000.book 34 ページ２０１２年４月１８日　水曜日　午後９時３分

Summary of Contents for 2012 NC700D



































































































































Search results

Summary of Contents for 2012 NC700D

Reviews:

Related manuals for 2012 NC700D

Brands by name

Popular brands

Honda 2012 NC700D, Owner'S Manual

Search results

Summary of Contents for 2012 NC700D

Reviews:

Related manuals for 2012 NC700D

Brands by name

Popular brands