background image

© 1999 American Honda Motor Co., Inc - All Rights Reserved.

 AII 20447 (9908)

3 of 10

KNEE BOLSTER

BOLTS

CONTROL UNIT

CX/DX

HX/LX/EX

DRIVER'S
DASHBOARD
LOWER COVER

SELF-TAPPING
SCREW

MOONROOF MODEL

RETAINING
CLIP

Tear off
this label.

NOTE: The Owner’s Manual included with the Security
Attachment should be placed in the glove box for future
reference. The Owner’s Manual included with the Security
System should be discarded.

1.

Make sure you have the anti-theft code for the radio,
then write down the frequencies for the preset
buttons.

2.

Disconnect the negative cable from the battery.

3.

Move the switch on the control unit into the correct
mode for the CX and DX models.

Customer Information: The information in this
installation instruction is intended for use only by
skilled technicians who have the proper tools,
equipment, and training to correctly and safely add
equipment to your car. These procedures should
not be attempted by “do-it-yourselfers.”

The knob is set
in this position
at the factory.

4.

Remove the driver's dashboard lower cover:

Remove the three screws.

Gently pull along the top to release the three
retaining clips.

Unplug the connector(s) and remove the cover.

5.

Remove the knee bolster (two bolts).

INSTALLATION

Summary of Contents for 08E55-S01-100H











Reviews: