Honda 08B23-SJC-100 Installation Instructions Manual Download Page 22

Page: 22 / 24

22 of 24

AII 32445 (0605)

4917060M

MODULATOR

BRACKET

AUDIO UNIT

SCREW

84. Set the FM modulator switch at 88.5. Using

isopropyl alcohol on a shop towel, clean the area
where the EPT sealer will attach. Using scissors,
cut one EPT sealer in half. Secure the FM
modulator cables to the FM modulator with one
EPT sealer half.

83. Secure the FM modulator bracket to the FM

modulator with one 5 x 8 mm washer-screw
(included with the monitor kit).

85. Using isopropyl alcohol on a shop towel, clean the

area where the EPT sealer will attach. Attach one
EPT sealer half that you cut into two in step 84 to
the audio unit.

4917030M

AUDIO UNIT

EPT SEALER

Cut in half in

step 84.

4917021M

MODULATOR

5 x 8 mm

WASHER-SCREW

(Included in the

monitor kit.)

MODULATOR

BRACKET

4917052M

MODULATOR

EPT SEALER

Cut in half.

MODULATOR

CABLE

SWITCH

86. Remove two screws from the audio unit/navigation

unit. Secure the FM modulator bracket to the
audio unit with the two screws you removed.

Summary of Contents for 08B23-SJC-100

























Search results

Summary of Contents for 08B23-SJC-100

Reviews:

Related manuals for 08B23-SJC-100

Brands by name

Popular brands

Honda 08B23-SJC-100, Installation Instructions Manual

Search results

Summary of Contents for 08B23-SJC-100

Reviews:

Related manuals for 08B23-SJC-100

Brands by name

Popular brands