background image

Page 6

SYMBOLS

Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the tool better and safer.

SYMBOL

NAME

EXPLANATION

Indicates danger, warning or caution. It means attention!!!
Your safety is involved.

Your manual contains special messages to bring
attention to potential safety concerns, machine damage
as well as helpful operating and servicing information.
Please read all the information carefully to avoid injury
and machine damage.

Wear eye, hearing, and head protection when operating
this equipment.

The SAFE-T-TIP nose guard on the guide bar helps
prevent kickback.

No smoking, sparks, or open flame.

Diagonal line across a symbol means this is prohibited
or should be avoided.

Hold and operate the saw properly with both hands.

Do not operate the saw using only one hand.

Engines produce carbon monoxide which is an odorless,
deadly poison. Do not operate in an enclosed area.

Danger – beware of kickback.

Avoid bar nose contact.

Wear non-slip gloves.

Safety Alert Symbol

Read Your Operator’s Manual

Eye, Hearing, and Head Protection

SAFE-T-TIP Nose Guard

No Smoking

Operate with Two

Hands

One Handed

Prohibited Symbol

Gloves

Bar Nose Contact

Kickback

Carbon Monoxide

Summary of Contents for UT10510





































Reviews: