CLEANING THE PRE-FILTER
NOTE:
For best performance,
vacuum the pre-filter once a
month under normal usage.
1. Unplug the air purifier.
2. Remove the True HEPA filter
as described in the Replacing
the True HEPA Filter section.
3. Vacuum the outside of the
True HEPA filter using the brush attachment of your vacuum
cleaner, cleaning it thoroughly.
4. Place the True HEPA filter back into the air purifier and close
grille.
5. Plug the power cord into a standard AC outlet.
TO CLEAN THE OIL TRAY
Open the oil tray and remove the
pad. Essential oil pads should be
changed when switching to a
different essential oil scent. If
continuing to use the same scent,
set the essential oil pad aside for
reuse. Wipe down the inside of
the oil tray with a soft cloth. Place the essential oil pad back in the
tray and close.
NOTE:
Leave the essential oil pad out of the oil tray when storing.
FOR BEST PERFORMANCE
• NEVER use water or any household cleaners or detergents to
clean the True HEPA filter.
• Clean off the outside of the unit with a dry cloth as needed.
• NEVER use water, wax, polish, or any chemical solution to clean
the outside of the unit.
• Clean off the grille cover using a damp cloth or the brush
attachment of your vacuum as needed.
• Vacuum the pre-filter monthly under normal usage conditions.
• Replace the True HEPA filter every 12 months under normal
usage conditions.
• Always use a genuine HoMedics replacement filter for optimal
performance.
To purchase genuine HoMedics replacement/spare parts please
visit www.homedics.com.au
3 Pack of aroma pads - ARM-PAD3
Aroma tray - AP-T30WTARM
HEPA filter - AP-T30FL
UV-C Bulb – AP-UVC1
Cover & screws - APUVCCV
CLEANING & MAINTENANCE
PROBLEM
POSSIBLE CAUSE
SOLUTION
Unit will not operate
• Unit is not plugged in
• Power button not pressed
• No power to unit
• True HEPA filter is not installed correctly
• Grille cover is not installed correctly
• Plug unit in
• Press the power button to turn the power on
• Check fuses, try a different outlet
• Reinstall the True HEPA filter
• Reinstall the grille cover
Reduced airflow
• The back grille may be blocked
• Pre-filter needs vacuuming
• The True HEPA filter needs to be replaced
• Check to make sure nothing is blocking the back
grille and air outlet
• Vacuum the pre-filter with the brush
attachment of your vacuum cleaner
• Replace the True HEPA filter
Reduced odour removal
• The True HEPA filter needs to be replaced • Replace the True HEPA filter
Excessive noise
• The unit is not level
• Place the unit on a flat, level surface
Replace filter light remains lit
after filter replacement
• The replace filter indicator needs to be
reset
• Press and hold the ioniser button for 3 seconds
until the replace filter light turns off
Display lights are off
• Nightlight setting
• Press the nightlight button until the desired
lights are on/off
TROUBLESHOOTING
FILTER REPLACEMENT
REPLACE FILTER LIGHT
The replace filter light illuminates when it is time to replace the
True HEPA filter based on the air purifier’s hours of use.
REPLACING THE TRUE HEPA FILTER
For optimal performance, replace every 12 months under normal
usage conditions.
1. Unplug the air purifier. Pull the
indents on each side of the grille
cover.
2. Remove the grille cover and set
aside.
3. Pull the tabs to remove the old
filter.
4. With the filter tabs facing outward,
insert the new True HEPA filter.
5. Place the tabs at the bottom
of the grille cover into the
base of the air purifier. Gently
push the grille cover until it
snaps into place.
6. Plug the power cord into a standard
AC outlet and press the power
button Press and hold the ioniser
ION
button for 3 seconds to reset
the indicator.
UV-C BULB REPLACEMENT
REPLACING THE UV-C BULB
The UV-C bulb is designed to last for approximately 10,000
hours of use. The UV-C button on the control panel will flash
RED when the UV-C bulb burns out and needs to be replaced.
The UV-C button will change to blue once the bulb has been
replaced.
NOTE:
The air purifier will continue to operate without the UV-C
function when the UV-C bulb burns out.
CAUTION: Do not operate the air purifier without the
protective UV-C bulb cover.
CAUTION: Unplug the power cord before servicing or
replacing the UV-C bulb.
1. Unplug the air purifier and remove
the True HEPA filter. Using a
Phillips-head screwdriver (not
included), unscrew the 2 screws
located on the UV-C bulb cover.
2. Remove the cover to expose the
UV-C bulb.
3. Gently push from the sides and
rotate the UV-C bulb to remove.
4. Remove and replace the UV-C bulb.
Re-install the UV-C bulb cover, True
HEPA filter, and grille cover.
NOTE:
The UV-C bulb contains mercury (Hg).
