background image

10. Open the door panel (E). Place the gas cylinder into the gas cylinder support (K) and connect the regulator by 

      turning the black handle clockwise to tighten. To remove the regulator, turn the black handle counter-clockwise. 

      Secure the gas cylinder by tightening clockwise the retention point found on gas cylinder support (K), (see Figure 

      10), so that the gas cylinder cannot move from side to side or fall down. The knob on the control panel is turned 

      all the way to the “OFF” position when the fire pit in NOT in use.

retention point

K

 

black handle

 

K

E

E

 
     

CAUTION: 

Please be advised that this fire pit is equipped with natural lava rock that may crackle or pop the 

first time it is used. The lava rock has been pre-heat treated to release any natural inherent moisture. How-

ever, in rare cases on first time use, the lava rock may pop or burst causing small pieces of hot rock to 

potentially be a projectile. These hot pieces could cause injury or property damage. As a precaution, please 

follow these instructions the first time the fire pit is used:

(1). On first use, do not stand over or near the fire pit once lit.

(2). Light the fire pit and let it run on high for 20 minutes. 

(3). Once lit, do not go within 12 feet of the fire pit for at least the first 20 minutes on the first use to ensure 

       any  residual moisture trapped in the rocks gets released.

(4). After the first heating cycle there is little further concern. It is rare that any crackling will happen on the 

      first use,  this is simply a precaution. 

(5). Keep lava rock covered and dry while not in use to prevent additional moisture from getting in the rocks.

(6). If lava rocks are exposed to moisture after first use, run the burner on low to gradually warm and dry the 

      rocks before repeating steps 1 through 3.

    

Figure 9

Figure 10

07

9. Open the box of lava rocks, put the lava rocks (L) into the fire bowl of the fire table (B), (see Figure 9). A gas fire 

    pit requires 6.6 lbs lava rocks.

    WARNING:

 Keep children away during assembly, as this item contains lava rock, which are small pieces and can     

    be swallowed by children. 

    NOTE:

 Leave the pilot box uncovered by the lava rock.

pilot box

L

B

Summary of Contents for F210004-B2













Reviews: