background image

After you exit the Configuration Page, when the light level reaches the “light” threshold, the 
display will illuminate to the brighter settings; when the light level reaches the “dark” threshold, 
the display will dim to the darker setting. 
 
Once configured, to disable the ambient settings so that the screen is always at the same 
intensity, set the “Brightness” to the desired level, and then press the [Light] icon immediately 
followed by the [Dark] icon.  By default, the ambient settings are disabled. 
 
Firmware Version 
 
The version of installed firmware in the OmniTouch 5.7e is displayed above the [OK] button on 
the Screen Setup page. 
 
After all screen parameters have been entered or confirmed, press the “Cameras” tab to 
configure HAI Camera Servers or press the [OK] button at the bottom of the page to save the 
settings and connect to the configured HAI controller. 
 

Cameras 
 

The Cameras page allows you to add up to 2 HAI 87A00-1 Camera Servers (4 cameras per HAI 
Camera Server) to the OmniTouch 5.7e design without using HAI Automation Studio.  This 
allows you to easily configure up to 8 cameras to be displayed on the OmniTouch 5.7e without 
any additional software or configuration. 

 
 

 

 
 

 

12 

Summary of Contents for 53A00-2





















Reviews: