background image

 

    

 

P a g e

 | 

18

 

Kakute F7

 

Configuration 

Click on the “Configuration” tab on the right side of the window. Scroll down to the “Other Features” 
section. 

 

If you are using any kind of telemetry (SmartPort, Crossfire, 
etc.), enable TELEMETRY. 

 

If you are using a programmable LED strip, enable 
LED_STRIP. 

 

Air Mode increases authority when the throttle is all the 
way down. We recommend leaving this option on all the 
time. 

 

The Kakute F7 has built-in Betaflight OSD. The OSD option 
should always be enabled. 

 

If you are using ESC telemetry, enable the ESC_SENSOR 
option. 

 

The ANTI_GRAVITY option increases the stability of the 
copter when the throttle is raised or lowered quickly. We 
recommend enabling this option, and setting Anti Gravity 
Gain to 3.0 in the PID Tuning tab. Detailed instructions for 
tuning this value are outside the scope of this manual, but 
this default setting will work well for most quads. 

Next, go to the Receiver section of the “Configuration” tab. Since the Kakute F7 only supports serial-type 
receivers, configuration of this section is simple. 

 

Set the Receiver Mode to “Serial-based 
receiver”. 

 

Set the Serial Receiver Provider to the type 
that matches what kind of receiver you have. 
FrSky and other SBUS receiver should use 
SBUS. Spektrum Satellite receivers should use 
SPEKTRUM2048 or SPEKTRUM1024 depending 
on whether they are DSM2 or DSMX. FlySky 
receivers use iBus. Crossfire receivers use CRSF.  

These are the most common serial receiver types that are likely to be encountered. 

 

Summary of Contents for 11033






























Reviews: