HOLOPHANE Phuzion PHZL Installation And Maintenance Manual Download Page 6

HOLOPHANE

®

 

Phuzion

TM 

 PHZL Remote 

Installation and 

 

Highbay Luminaire 

Maintenance 

 

 

Manual 

 

 

 

IM-394 

2.8 Electrical Housing - Hook Mounting 
2.8.1

 Mounting hook (shipped separate from RPHZL 

fixture) is installed via the threaded hole at the top of the 
Electrical Housing junction box (Figure 5) 

2.8.2

 Apply sealant evenly to threads of the hook 

assembly.

 

2.8.3 

Thread hook tightly into top of Electrical housing 

junction box.

 

2.8.4 

Wipe away excess adhesive. 

2.8.5 

Hang the Electrical Housing on a structure that is 

properly sized and attached to support the weight of the 
Electrical Housing 

2.8.6 

Tighten screw in hook to 25-35 ft lbs. 

2.8.7 

Proceed to section 2.8 for wiring.   

 

2.6 Electrical Housing - Surface Mounting (Figure 6)

 

2.6.1 

Mount Electrical Housing to vertical or horizontal 

surface that can support the weight of the Electrical 
Housing.  If mounted vertically, orient Electrical Housing 
with hook on top. 

2.6.2

 Mounting position locations are show in Figure 6

 

2.6.3 

Mount Electrical Housing using fasteners properly 

sized to support the weight of the Electrical Housing 
(fasteners not provided). 
 

Figure 6 

 

GR2435 

 
 
 
 
 
 
 

2.10 Safety Chain Option 
2.10.1 

Safety chain option comes attached to the Optical 

housing.  Attach loose end to building structure leaving 
no more than three inches of slack.  Leaving more than 
three inches of slack will allow a long free-fall, resulting 
in a large impact load and possible structural failure. 
 

WARNING 

LEAVE  NO  MORE THAN  THREE  INCHES  OF  SLACK 
IN  THE  CHAIN  WHEN  ATTACHING  TO  THE 
BUILDING  STRUCTURE.    LEAVING  MORE  SLACK 
WILL ALLOW A LONGER FREE-FALL, A RESULTING 
LARGER 

IMPACT 

LOAD 

AND 

POSSIBLE 

STRUCTURAL FAILURE.  FAILURE TO INSTALL THE 
CHAIN  AS  INSTRUCTED  MAY  RESULT  IN  INJURY 
OR DEATH OR SIGNIFICANT PROPERTY DAMAGE. 
 

AVERTISSEMENT 

NE PAS LAISSER PLUS DE TROIS POUCES DE JEU 
À  LA  CHAINE  LORS  DE  LA  FIXATION  À  LA 
STRUCTURE DE  L'ÉDIFICE.  LAISSER  PLUS  DE  JEU 
PERMETTRAIT  UNE  PLUS  LONGUE  CHUTE  LIBRE, 
UN IMPACT DE CHARGE PLUS IMPORTANT ET UNE 
POSSIBLE  DÉFAILLANCE  DE  LA  STRUCTURE.  NE 
PAS 

INSTALLER 

LA 

CHAÎNE 

SELON 

LES 

INSTRUCTIONS 

PEUT 

PROVOQUER 

DES 

BLESSURES, 

LA 

MORT 

OU 

DE 

SÉRIEUX 

DOMMAGES MATÉRIELS. 

Summary of Contents for Phuzion PHZL








Reviews: