PRE-OPERATING INSTRUCTIONS
1. Make sure the unit is in the OFF position before plugging the heater
into the outlet.
2. Place heater on firm level surface.
3. Avoid overloading your circuit by not using other high wattage
appliances in the same outlet.
NOTE:
This unit is for FLOOR USE ONLY.
OPERATING INSTRUCTIONS
1. Set the heat selector switch to the OFF position.
2. Plug in heater.
3. For heater operation, press the MODE button the back of the unit
until the LED on the front of the unit indicates either HIGH or LOW.
NOTE:
The power light will remain lit during operation.
NOTE:
Check to be sure that there are no objects between you and
the heater. Such objects will absorb the heat and prevent it from
reaching you.
NOTE:
The parabolic design of the reflector focuses heat at people
and objects located 3 to 10 feet in front of the heater. Therefore, to
fully enjoy the sun-like warmth produced by the heater, it must be
positioned at least three feet from you. Placing it closer is not
recommended. Try different positions until you find the optimal one
for you.
OSCILLATION INSTRUCTIONS
1. Press the OSCILLATE button once to turn on Oscillation feature.
2. Press OSCILLATION again to turn it off.
3. Do not manually turn the unit, as it is designed to turn only by
motorized oscillation.
REMOTE CONTROL INSTRUCTIONS
Insert 2 "AAA" batteries (not included) into the remote control.
POWER:
To turn the unit On or Off, press the MODE button.
MODES:
To select the heat setting, press the MODE button to toggle
between LOW and HIGH heat settings.
OSCILLATION:
To start oscillation, press the OSC button once. A
light on the front power lens will illuminate, indicating the oscillation
is on. To stop oscillation press the button again.
BATTERY WARNING:
• DO NOT mix old and new batteries.
• DO NOT mix alkaline, standard (carbon-zinc), or rechargeable
(nickel-cadmium) batteries.
CLEANING/MAINTENANCE
During Season Care:
1. Always unplug the heater before cleaning.
2. Clean the unit with a soft cloth moistened with a mild soap
solution.
3. NEVER use abrasive or flammable solvents to clean the unit.
4. To clean parabolic reflector dish we recommend the use of a thin
brush. This brush can be inserted through the front grill in order
to move any dust or debris to the lower edge of the reflector dish.
DO NOT REMOVE THE GRILL. Use a vacuum to remove dust or
debris from the outer edge of the reflector dish.
5. After cleaning, be sure to completely dry the unit with a cloth or
towel.
After Season Care:
1. Store heater in a cool, dry location.
2. The manufacturer recommends that you store the unit in its
original carton.
TROUBLESHOOTING
If your heater fails to operate:
• UNPLUG THE UNIT.
• Make sure the electrical outlet or circuit breaker is working.
• Check for obstructions. If you find an obstruction turn the heater
OFF, and unplug the unit. Carefully remove the obstruction and
follow the reset instructions.
• The temperature may be set too low. Turn the heat selector knob
clockwise until the heater restarts.
• Make sure the selector is in LOW or HIGH setting.
Please DO NOT attempt to open or repair the heater.
Please see the Warranty for Service Instructions.
P L E A S E R E A D A N D S AV E T H E S E
I M P O R TA N T S A F E T Y I N S T R U C T I O N S
FEATURES-OPERATIONS
When using electrical appliances, basic safety precautions should
always be followed to reduce the risk of fire, electric shock, and injury
to persons, including the following:
1. Read all instructions before using the appliance.
2. To avoid fire or shock hazard, plug the appliance directly into a
120V AC electrical outlet.
3. The heater is hot when in use. To avoid burns, DO NOT let bare
skin touch hot surfaces. If provided, use handles when moving
this heater. Keep combustible materials, such as furniture, pillows,
bedding, papers, clothes, and curtains at least 3 ft (0.9 m) from
the front of the heater and keep them away from the sides and
rear.
4. DO NOT run cord under carpeting. DO NOT cover cord with throw
rugs, runners, or the like. Arrange cord away from traffic area
and where it will not be tripped over.
5. This heater is not intended for use in bathrooms, laundry areas
and similar indoor location. NEVER locate heater where it may fall
into a bathtub or other water container.
6. Extreme caution is necessary when any heater is used by, or near
children or invalids, and whenever the heater is left operating and
unattended.
7. Always unplug the heater when not in use.
8. When unplugging, be sure to pull by the plug and not the cord.
9. DO NOT insert or allow foreign objects to enter any ventilation or
exhaust opening as this may cause an electric shock or fire, or
damage the heater.
10.DO NOT operate heater with a damaged cord or plug, or after the
heater malfunctions, has been dropped or damaged in any
manner. Return appliance to manufacturer for examination,
electrical or mechanical adjustment, or repair.
11.A heater has hot and arcing or sparking parts inside. DO NOT use
it in areas where gasoline, paint, or flammable liquids are used or
stored.
12.Use appliance only for intended household use as described in this
manual. Any other use not recommended by the manufacturer may
cause fire, electric shock, or injury to persons. The use of
attachments not recommended or sold by The Holmes Group may
cause hazards.
13.DO NOT use outdoors.
14.To prevent a possible fire, DO NOT block air intakes or exhaust in
any manner. DO NOT use on soft surfaces, like a bed, where
openings may become blocked.
15.To disconnect heater, turn controls to OFF, then remove plug from
outlet.
16.Avoid the use of an extension cord because the extension cord
may overheat and cause a risk of fire. However, if you have to
use an extension cord, the cord shall be No. 14 AWG minimum size
and rated not less than 1875 watts.
17.If the heater will not operate, see specific instructions on Auto
Safety Shut-off.
18.DO NOT attempt to repair or adjust any electrical or mechanical
functions on this unit. Doing so will void your warranty. The inside
of the unit contains no user serviceable parts. All servicing should
be performed by qualified personnel only.
19.Discontinue use if plug or outlet is hot. It is recommended that the
outlet be replaced if plug or outlet is hot to touch.
PLEASE READ AND SAVE
THESE IMPORTANT
SAFETY INSTRUCTIONS
THIS PRODUCT IS EQUIPPED WITH A POLARIZED AC
(Alternating Current) PLUG (a plug having one blade wider
than the other). This plug will fit into the power outlet only
one way. If the plug does not fit fully into the outlet, reverse
the plug. If it still does not fit, contact qualified personnel to
install the proper outlet.
DO NOT DEFEAT THE SAFETY PURPOSE OF THIS
POLARIZED PLUG IN ANY WAY
This heater is equipped with a patented, technologically-advanced safety
system that requires the user to reset the heater if there is a potential
overheat situation. When a potential overheat temperature is reached,
the system will automatically shut the heater off. It can only resume
operation when the user resets the unit.
To Reset the Heater:
1. Unplug the heater and wait 10 minutes for the unit to cool down.
2. After the 10 minutes, push the RESET button.
3. Plug the unit in again and operate normally.
Tip-Over Protection:
When the unit is accidentally knocked over, it will automatically shut off.
To reset, simply place the heater in an upright position.
ASSEMBLY INSTRUCTIONS
1. Carefully remove your heater from the box. Please save the
carton for off-season storage.
2. Place heater on firm level surface.
3. Make sure the power cord comes straight out of the hole in the
middle of the base without obstructing the channels on the bottom
of the base.
4. Place the assembled metal base tubing in the channels on the
bottom of the base.(See Fig. 2)
5. Secure metal tubing to the base with the three screws provided.
6. Turn heater upright and follow operating instructions below.
AUTO SAFETY SHUT-OFF WITH MANUAL RESET
TECHNICAL SPECIFICATIONS
• Wattage: 1100 W (+5% –15%)
• Working Voltage: 120v AC/60Hz
Figure 2
Figure 1
HRH84803EM2_ENG.qxd 8/5/03 10:37 AM Page 2
