manualshive.com logo in svg

Hoist Fitness HD1400, Owner'S Manual

Share
Download
Hoist Fitness HD1400 Owner'S Manual Download Page 39

Page - 38

HD1400 Assembly

OW N E R S

M A N U A L

Continued: GENERAL MAINTENANCE INFORMATION

Cable Tension:

Seat Sleeves, Turcite Bushings:

Linear Bearings:

F

Referring to the Assembly/Owners Manual, check all cable bolts and attachments to be sure they are properly

attached.

Check slack in cables and readjust cable tension if needed.

Wipe down adjusting tubes with a dust free rag before applying lubricant.

Lubricate seat sleeves and turcite bushings with a Silicon or Teflon based lubricant spray.

Referring to the Assembly/ Owners manual carefully dis-assemble the bearing from its housing and place a finger

full of light grease (lithium, super lube, etc.) into the inside of the bearing. Using your finger, press the grease into the
ball-bearings and their tracks. Repeat until the ball-bearing tracks are full of grease. Insert the shaft back into the
bearing and wipe off excess grease.

F

F

F

F

PLEASE KEEP THIS FOR YOUR RECORDS.

Summary of Contents for HD1400










































Reviews:

No comments

Brands by name

Popular brands

Load more brands