Hobart Multi-Handler 200, Owner'S Manual

Page: 14 / 76

.
A complete Parts List is available at www.HobartWelders.com
OM-285922 Page 11
SECTION 4 − SPECIFICATIONS
4-1. Serial Number And Rating Label Location
The serial number and rating information for this product is located on the back of unit. Use rating label to determine input power requirements and/or
rated output. For future reference, write serial number in space provided on back cover of this manual.
4-2. Software Licensing Agreement
The End User License Agreement and any third-party notices and terms and conditions pertaining to third-party software can be found at
https://www.hobartwelders.com/eula
.
and are incorporated by reference herein.
4-3. Information About Default Weld Parameters And Settings
NOTICE − Each welding application is unique. Although certain Miller Electric products are designed to determine and default to certain typical welding
parameters and settings based upon specific and relatively limited application variables input by the end user, such default settings are for reference
purposes only; and final weld results can be affected by other variables and application-specific circumstances. The appropriateness of all parameters
and settings should be evaluated and modified by the end user as necessary based upon application-specific requirements. The end user is solely
responsible for selection and coordination of appropriate equipment, adoption or adjustment of default weld parameters and settings, and ultimate
quality and durability of all resultant welds. Miller Electric expressly disclaims any and all implied warranties including any implied warranty of fitness
for a particular purpose.
4-4. Unit Specifications For MIG (GMAW)
.
Do not use information in unit specifications table to determine electrical service requirements. See Sections 5-3, 5-5, and 5-6 for information on
connecting input power.
Input
Voltage
Rated Welding
Output
Amperage
Range
Maximum Open-
Circuit Voltage
DC
Amperes Input at Rated
Load Output, 50/60 Hz,
Single-Phase
120 VAC
100 A @ 19.0 Volts DC
40% Duty Cycle
30 − 120 63 20.9
Wire Type
And Diameter
Solid/Stainless Flux Cored Wire Feed Speed Range
.024 - .035 in.
(0.6 - 0.8 mm)
.030 - .035 in.
(0.8 - 0.9 mm)
60 − 650 IPM (1.5 − 16.5 m/min)
240 VAC
200 A @ 24.0 Volts DC
15% Duty Cycle
140 A @ 21.0 Volts DC
40% Duty Cycle
30 − 200 63
25.0
25.1
Wire Type
And Diameter
Solid/Stainless Flux Cored Wire Feed Speed Range
.024 − .035 in.
(0.6 − 0.9 mm)
.030 − .045 in.
(0.8 − 1.2 mm)
60 − 650 IPM (1.5 − 16.5 m/min)
4-5. Unit Specifications For TIG (GTAW)
.
Do not use information in unit specifications table to determine electrical service requirements. See Sections 5-3, 5-5, and 5-6 for information on
connecting input power.
Input
Voltage
Rated Welding
Output
Amperage
Range
Maximum Open-
Circuit Voltage
DC
Amperes Input at Rated
DC Load Output,
50/60 Hz, Single-Phase
120 VAC
140 A @ 15.6 Volts AC/DC
20% Duty Cycle
20 − 140
63 25.0
240 VAC
200 A @ 18.0 Volts AC/DC
20% Duty Cycle
20 − 200 63 20.0
4-6. Unit Specifications For Stick (SMAW)
.
Do not use information in unit specifications table to determine electrical service requirements. See Sections 5-3, 5-5, and 5-6 for information on
connecting input power.
Input
Voltage
Rated Welding
Output
Amperage
Range
Maximum Open-
Circuit Voltage
DC
Amperes Input at Rated
DC Load Output,
50/60 Hz, Single-Phase
120 VAC
80 A @ 23.2 Volts AC/DC
40% Duty Cycle
30 − 100 63 19.2
240 VAC
170 A @ 28.0 Volts AC/DC
15% Duty Cycle
30 − 200 63 23.5