Hobart Welding Products 0 Owner'S Manual Download

Page: 28 / 68

OM-945 Page 24

7-2. Optional Generator Power Receptacles

If unit does not have GFCI re-
ceptacles, use GFCI-

protected extension cord.

Combined output of all receptacles

limited to 10 kVA/kW rating of the

generator.

GFCI Receptacle Option

120 V 20 A AC GFCI Recep-

tacles GFCI2 and GFCI3

GFCI2 and GFCI3 supply 60 Hz

single-phase power at weld/power

speed. Maximum output from

GFCI2 or GFCI3 is 2.4 kVA/kW. Cir-

cuit protection is the same as stan-

dard receptacles.
If a ground fault is detected, the

GFCI Reset button pops out and

the circuit opens to disconnect the

faulty equipment. Check for

damaged tools, cords, plugs, etc.

connected to the receptacle. Press

button to reset receptacle and

resume operation.

At least once a month, run

engine at weld/power speed

and press Test button to verify

GFCI is working properly.

Ref. 226 427-A

Notes

Over 80,000 trained

since 1930!

400 Trade Square East, Troy, Ohio 45373

1-800-332-9448 www.welding.org

Start Your Professional

Welding Career Now!

Summary of Contents for 0





































































Search results

Summary of Contents for 0

Reviews:

Related manuals for 0

Brands by name

Popular brands

Hobart Welding Products 0, Owner'S Manual

Search results

Summary of Contents for 0

Reviews:

Related manuals for 0

Brands by name

Popular brands