background image

Intesis

TM

 INMBSPAN001A000

 

User’s Manual r1.

3 EN

 

 

 

 

  

 

 

 

 

 

 

© HMS Industrial Networks S.L.U. - All rights reserved 

This information is subject to change without notice

 

 

  URL    https://www.intesis.com  

 
 

                3 / 22

 

 

 
 

 

 

 

 

 

 

 

 

 

Important User Information 

Disclaimer 

The information in this document is for informational purposes only. Please inform HMS Industrial Networks 
of any inaccuracies or omissions found in this document. HMS Industrial Networks disclaims any responsibility 
or liability for any errors that may appear in this document. 

HMS Industrial Networks reserves the right to modify its products in line with its policy of continuous product 
development.  The  information  in  this  document  shall  therefore  not  be  construed  as  a  commitment  on  the 
part of HMS Industrial Networks and is subject to change without notice. HMS Industrial Networks makes no 
commitment to update or keep current the information in this document. 

The data, examples and illustrations found in this document are included for illustrative purposes and are only 
intended to help improve understanding of the functionality and handling of the product. In view of the wide 
range of possible applications of the product, and because of the many variables and requirements associated 
with  any  particular  implementation,  HMS  Industrial  Networks  cannot  assume  responsibility  or  liability  for 
actual use based on the data, examples or illustrations included in this document nor for any damages incurred 
during  installation  of  the  product.  Those  responsible  for  the  use  of  the  product  must  acquire  sufficient 
knowledge  in  order  to  ensure  that  the  product  is  used  correctly  in  their  specific  application  and  that  the 
application meets all performance and safety requirements including any applicable laws, regulations, codes 
and standards. Further, HMS Industrial Networks will under no circumstances assume liability or responsibility 
for any problems that may arise as a result from the use of undocumented features or functional side effects 
found outside the documented scope of the product. The effects caused by any direct or indirect use of such 
aspects of the product are undefined and may include e.g. compatibility issues and stability issues. 

 

 

 
 
 
 
 
 
 
 
 

Summary of Contents for INTESIS INMBSPAN001A000























Reviews: