background image

                                                                                                                        

 

AB7609 Installation Guide

 

6

© 2005 HMS Industrial Networks.  

Connecting to PROFIBUS

PROFIBUS Connector

PROFIBUS is connected to the 9-pin D-Subminiature connector located next to 

the PROFIBUS termination DIP switch.

Setting the PROFIBUS Network Address

The PROFIBUS network address is set using two rotary switches on the end of the 

Anybus-X. Each switch sets a digit of the address from 1 to 9, allowing for a range 

of network addresses from 1 to 99. 

The rotary switch nearest the 9-pin D-Sub PROFIBUS network connector sets the 

10’s digit. The other switch sets the 1’s digit

Hint:

 If you look at the end of the Anybus-X with the 9-pin D-Sub PROFIBUS 

network connector on your left, the node address is easier to read.

Setting the PROFIBUS Baud Rate

The PROFIBUS baud rate is set during the configuration of the PROFIBUS Mas-

ter. The Anybus-X has automatic baud rate detection so no configuration of the 

Anybus-X itself is required. 

Setting the PROFIBUS Network Termination

If network termination is required at the Anybus-X, set the termination DIP 

switch to the ON position.   

Note:

 If an external termination connector is used, the termination switch must be 

in the OFF position.

(6) +5V Bus
(3) B-Line

GND Bus (5)

RTS (4)

A-Line (8)

Summary of Contents for Anybus-X AB7609












Reviews: